IDEAS home Printed from https://ideas.repec.org/a/gam/jeners/v9y2016i12p1009-d84038.html
   My bibliography  Save this article

Development of Correlations for Windage Power Losses Modeling in an Axial Flux Permanent Magnet Synchronous Machine with Geometrical Features of the Magnets

Author

Listed:
  • Alireza Rasekh

    (Department of Flow, Heat and Combustion Mechanics, Faculty of Engineering and Architecture, Ghent University, B-9000 Ghent, Belgium)

  • Peter Sergeant

    (Department of Electrical Energy, Systems and Automation, Faculty of Engineering and Architecture, Ghent University, B-9000 Ghent, Belgium
    Flanders Make, the Strategic Research Centre for the Manufacturing Industry, B-8500 Kortrijk, Belgium)

  • Jan Vierendeels

    (Department of Flow, Heat and Combustion Mechanics, Faculty of Engineering and Architecture, Ghent University, B-9000 Ghent, Belgium)

Abstract

In this paper, a set of correlations for the windage power losses in a 4 kW axial flux permanent magnet synchronous machine (AFPMSM) is presented. In order to have an efficient machine, it is necessary to optimize the total electromagnetic and mechanical losses. Therefore, fast equations are needed to estimate the windage power losses of the machine. The geometry consists of an open rotor–stator with sixteen magnets at the periphery of the rotor with an annular opening in the entire disk. Air can flow in a channel being formed between the magnets and in a small gap region between the magnets and the stator surface. To construct the correlations, computational fluid dynamics (CFD) simulations through the frozen rotor (FR) method are performed at the practical ranges of the geometrical parameters, namely the gap size distance, the rotational speed of the rotor, the magnet thickness and the magnet angle. Thereafter, two categories of formulations are defined to make the windage losses dimensionless based on whether the losses are mainly due to the viscous forces or the pressure forces. At the end, the correlations can be achieved via curve fittings from the numerical data. The results reveal that the pressure forces are responsible for the windage losses for the side surfaces in the air-channel, whereas for the surfaces facing the stator surface in the gap, the viscous forces mainly contribute to the windage losses. Additionally, the results of the parametric study demonstrate that the overall windage losses in the machine escalate with an increase in either the rotational Reynolds number or the magnet thickness ratio. By contrast, the windage losses decrease once the magnet angle ratio enlarges. Moreover, it can be concluded that the proposed correlations are very useful tools in the design and optimizations of this type of electrical machine.

Suggested Citation

  • Alireza Rasekh & Peter Sergeant & Jan Vierendeels, 2016. "Development of Correlations for Windage Power Losses Modeling in an Axial Flux Permanent Magnet Synchronous Machine with Geometrical Features of the Magnets," Energies, MDPI, vol. 9(12), pages 1-17, November.
  • Handle: RePEc:gam:jeners:v:9:y:2016:i:12:p:1009-:d:84038
    as

    Download full text from publisher

    File URL: https://www.mdpi.com/1996-1073/9/12/1009/pdf
    Download Restriction: no

    File URL: https://www.mdpi.com/1996-1073/9/12/1009/
    Download Restriction: no
    ---><---

    References listed on IDEAS

    as
    1. Wei Hua & Ling Kang Zhou, 2015. "Investigation of a Co-Axial Dual-Mechanical Ports Flux-Switching Permanent Magnet Machine for Hybrid Electric Vehicles," Energies, MDPI, vol. 8(12), pages 1-19, December.
    2. Sergeant, Peter & Vansompel, Hendrik & Dupré, Luc, 2016. "Influence of stator slot openings on losses and torque in axial flux permanent magnet machines," Mathematics and Computers in Simulation (MATCOM), Elsevier, vol. 130(C), pages 22-31.
    3. Xiang Luo & Shuangxia Niu, 2016. "Maximum Power Point Tracking Sensorless Control of an Axial-Flux Permanent Magnet Vernier Wind Power Generator," Energies, MDPI, vol. 9(8), pages 1-17, July.
    4. Yunkai Huang & Baocheng Guo & Ahmed Hemeida & Peter Sergeant, 2016. "Analytical Modeling of Static Eccentricities in Axial Flux Permanent-Magnet Machines with Concentrated Windings," Energies, MDPI, vol. 9(11), pages 1-19, October.
    5. Mecrow, B.C. & Jack, A.G., 2008. "Efficiency trends in electric machines and drives," Energy Policy, Elsevier, vol. 36(12), pages 4336-4341, December.
    6. Yunchong Wang & Shuangxia Niu & Weinong Fu, 2015. "Electromagnetic Performance Analysis of Novel Flux-Regulatable Permanent Magnet Machines for Wide Constant-Power Speed Range Operation," Energies, MDPI, vol. 8(12), pages 1-14, December.
    7. Jing Zhao & Bin Li & Zhongxin Gu, 2015. "Research on an Axial Flux PMSM with Radially Sliding Permanent Magnets," Energies, MDPI, vol. 8(3), pages 1-22, February.
    Full references (including those not matched with items on IDEAS)

    Citations

    Citations are extracted by the CitEc Project, subscribe to its RSS feed for this item.
    as


    Cited by:

    1. Abdalla Hussein Mohamed & Ahmed Hemeida & Alireza Rasekh & Hendrik Vansompel & Antero Arkkio & Peter Sergeant, 2018. "A 3D Dynamic Lumped Parameter Thermal Network of Air-Cooled YASA Axial Flux Permanent Magnet Synchronous Machine," Energies, MDPI, vol. 11(4), pages 1-16, March.

    Most related items

    These are the items that most often cite the same works as this one and are cited by the same works as this one.
    1. Feng Chai & Yunlong Bi & Yulong Pei, 2017. "Magnet Shape Optimization of Two-Layer Spoke-Type Axial Flux Interior Permanent Magnet Machines," Energies, MDPI, vol. 11(1), pages 1-14, December.
    2. Peixin Liang & Yulong Pei & Feng Chai & Kui Zhao, 2016. "Analytical Calculation of D - and Q -axis Inductance for Interior Permanent Magnet Motors Based on Winding Function Theory," Energies, MDPI, vol. 9(8), pages 1-11, July.
    3. Jyun-You Chen & Shih-Chin Yang & Kai-Hsiang Tu, 2018. "Comparative Evaluation of a Permanent Magnet Machine Saliency-Based Drive with Sine-Wave and Square-Wave Voltage Injection," Energies, MDPI, vol. 11(9), pages 1-15, August.
    4. Hina Usman & Junaid Ikram & Khurram Saleem Alimgeer & Muhammad Yousuf & Syed Sabir Hussain Bukhari & Jong-Suk Ro, 2021. "Analysis and Optimization of Axial Flux Permanent Magnet Machine for Cogging Torque Reduction," Mathematics, MDPI, vol. 9(15), pages 1-14, July.
    5. Jianfei Zhao & Minqi Hua & Tingzhang Liu, 2018. "Research on a Sliding Mode Vector Control System Based on Collaborative Optimization of an Axial Flux Permanent Magnet Synchronous Motor for an Electric Vehicle," Energies, MDPI, vol. 11(11), pages 1-16, November.
    6. Nikola Lopac & Neven Bulic & Niksa Vrkic, 2019. "Sliding Mode Observer-Based Load Angle Estimation for Salient-Pole Wound Rotor Synchronous Generators," Energies, MDPI, vol. 12(9), pages 1-22, April.
    7. Du Plessis, Gideon Edgar & Liebenberg, Leon & Mathews, Edward Henry, 2013. "The use of variable speed drives for cost-effective energy savings in South African mine cooling systems," Applied Energy, Elsevier, vol. 111(C), pages 16-27.
    8. Thirugnanasambandam, M. & Hasanuzzaman, M. & Saidur, R. & Ali, M.B. & Rajakarunakaran, S. & Devaraj, D. & Rahim, N.A., 2011. "Analysis of electrical motors load factors and energy savings in an Indian cement industry," Energy, Elsevier, vol. 36(7), pages 4307-4314.
    9. Alexandra C. Barmpatza & Joya C. Kappatou, 2020. "Study of a Combined Demagnetization and Eccentricity Fault in an AFPM Synchronous Generator," Energies, MDPI, vol. 13(21), pages 1-17, October.
    10. Paramonova, Svetlana & Nehler, Therese & Thollander, Patrik, 2021. "Technological change or process innovation – An empirical study of implemented energy efficiency measures from a Swedish industrial voluntary agreements program," Energy Policy, Elsevier, vol. 156(C).
    11. Vannakone Lounthavong & Warat Sriwannarat & Apirat Siritaratiwat & Pirat Khunkitti, 2019. "Optimal Stator Design of Doubly Salient Permanent Magnet Generator for Enhancing the Electromagnetic Performance," Energies, MDPI, vol. 12(16), pages 1-12, August.
    12. Hosain, Md Lokman & Bel Fdhila, Rebei & Rönnberg, Kristian, 2017. "Taylor-Couette flow and transient heat transfer inside the annulus air-gap of rotating electrical machines," Applied Energy, Elsevier, vol. 207(C), pages 624-633.
    13. Yubin Wang & Guangyong Yang & Xinkai Zhu & Xianglin Li & Wenzhong Ma, 2018. "Electromagnetic Characteristics Analysis of a High-Temperature Superconducting Field-Modulation Double-Stator Machine with Stationary Seal," Energies, MDPI, vol. 11(5), pages 1-13, May.
    14. Saidur, R. & Rahim, N.A. & Ping, H.W. & Jahirul, M.I. & Mekhilef, S. & Masjuki, H.H., 2009. "Energy and emission analysis for industrial motors in Malaysia," Energy Policy, Elsevier, vol. 37(9), pages 3650-3658, September.
    15. Dongran Song & Jian Yang & Mei Su & Anfeng Liu & Yao Liu & Young Hoon Joo, 2017. "A Comparison Study between Two MPPT Control Methods for a Large Variable-Speed Wind Turbine under Different Wind Speed Characteristics," Energies, MDPI, vol. 10(5), pages 1-18, May.
    16. Abdelaziz, E.A. & Saidur, R. & Mekhilef, S., 2011. "A review on energy saving strategies in industrial sector," Renewable and Sustainable Energy Reviews, Elsevier, vol. 15(1), pages 150-168, January.
    17. Saidur, R. & Mahlia, T.M.I., 2010. "Energy, economic and environmental benefits of using high-efficiency motors to replace standard motors for the Malaysian industries," Energy Policy, Elsevier, vol. 38(8), pages 4617-4625, August.
    18. Saidur, R. & Rahim, N.A. & Hasanuzzaman, M., 2010. "A review on compressed-air energy use and energy savings," Renewable and Sustainable Energy Reviews, Elsevier, vol. 14(4), pages 1135-1153, May.
    19. Lei Xu & Mingyao Lin & Xinghe Fu & Kai Liu & Baocheng Guo, 2017. "Analytical Calculation of the Magnetic Field Distribution in a Linear and Rotary Machine with an Orthogonally Arrayed Permanent Magnet," Energies, MDPI, vol. 10(4), pages 1-18, April.
    20. Milad Maralani & Milad Maralani & Basil Sharp & Golbon Zakeri, 2016. "The Potential Impact of Industrial Energy Savings on The New Zealand Economy," EcoMod2016 9308, EcoMod.

    Corrections

    All material on this site has been provided by the respective publishers and authors. You can help correct errors and omissions. When requesting a correction, please mention this item's handle: RePEc:gam:jeners:v:9:y:2016:i:12:p:1009-:d:84038. See general information about how to correct material in RePEc.

    If you have authored this item and are not yet registered with RePEc, we encourage you to do it here. This allows to link your profile to this item. It also allows you to accept potential citations to this item that we are uncertain about.

    If CitEc recognized a bibliographic reference but did not link an item in RePEc to it, you can help with this form .

    If you know of missing items citing this one, you can help us creating those links by adding the relevant references in the same way as above, for each refering item. If you are a registered author of this item, you may also want to check the "citations" tab in your RePEc Author Service profile, as there may be some citations waiting for confirmation.

    For technical questions regarding this item, or to correct its authors, title, abstract, bibliographic or download information, contact: MDPI Indexing Manager (email available below). General contact details of provider: https://www.mdpi.com .

    Please note that corrections may take a couple of weeks to filter through the various RePEc services.

    IDEAS is a RePEc service. RePEc uses bibliographic data supplied by the respective publishers.