IDEAS home Printed from https://ideas.repec.org/a/eee/reensy/v168y2017icp18-27.html
   My bibliography  Save this article

Unavailability model for demand-caused failures of safety components addressing degradation by demand-induced stress, maintenance effectiveness and test efficiency

Author

Listed:
  • Martorell, P.
  • Martón, I.
  • Sánchez, A.I.
  • Martorell, S.

Abstract

The reliability, availability and maintainability (RAM) modelling of safety equipment has long been a topic of major concern. Some RAM models have focused on explicitly addressing the effect of component degradation and surveillance and maintenance policies, searching for an optimum level of the safety component RAM by adjusting surveillance and maintenance related parameters. As regards the reliability contribution, these components normally have two main types of failure mode that contribute to the probability of failure on demand (PFD): (1) by demand-caused and (2) standby-related failures. The former is normally associated with a demand failure probability, which is affected by the degradation caused by demand-related stress. Surveillance testing therefore not only introduces a positive effect, but also an adverse one, which it compensates by performing maintenance activities to eliminate or reduce the accumulated degradation. This paper proposes a new model for the demand failure probability that explicitly addresses all aspects of the effect of demand-induced stress (mostly test-induced stress), maintenance effectiveness (PAS or PAR model) and test efficiency. A case study is included on an application to a typical motor-operated valve in a nuclear power plant.

Suggested Citation

  • Martorell, P. & Martón, I. & Sánchez, A.I. & Martorell, S., 2017. "Unavailability model for demand-caused failures of safety components addressing degradation by demand-induced stress, maintenance effectiveness and test efficiency," Reliability Engineering and System Safety, Elsevier, vol. 168(C), pages 18-27.
    • Handle: RePEc:eee:reensy:v:168:y:2017:i:c:p:18-27
    DOI: 10.1016/j.ress.2017.05.044
    as

    Download full text from publisher

    File URL: http://www.sciencedirect.com/science/article/pii/S0951832016309206
    Download Restriction: Full text for ScienceDirect subscribers only
    File URL: https://libkey.io/10.1016/j.ress.2017.05.044?utm_source=ideas
    LibKey link: if access is restricted and if your library uses this service, LibKey will redirect you to where you can use your library subscription to access this item
    ---><---

    As the access to this document is restricted, you may want to search for a different version of it.

    References listed on IDEAS

    as
    1. Vaurio, Jussi K., 2015. "A recursive framework for time-dependent characteristics of tested and maintained standby units with arbitrary distributions for failures and repairs," Reliability Engineering and System Safety, Elsevier, vol. 138(C), pages 154-162.
    2. Torres-Echeverría, A.C. & Martorell, S. & Thompson, H.A., 2011. "Modeling safety instrumented systems with MooN voting architectures addressing system reconfiguration for testing," Reliability Engineering and System Safety, Elsevier, vol. 96(5), pages 545-563.
    3. Martón, I. & Martorell, P. & Mullor, R. & Sánchez, A.I. & Martorell, S., 2016. "Optimization of test and maintenance of ageing components consisting of multiple items and addressing effectiveness," Reliability Engineering and System Safety, Elsevier, vol. 153(C), pages 151-158.
    4. KanÄ ev, DuÅ¡ko & ÄŒepin, Marko & Gjorgiev, Blaže, 2014. "Development and application of a living probabilistic safety assessment tool: Multi-objective multi-dimensional optimization of surveillance requirements in NPPs considering their ageing," Reliability Engineering and System Safety, Elsevier, vol. 131(C), pages 135-147.
    5. Sanchez, Ana & Carlos, Sofia & Martorell, Sebastian & Villanueva, Jose F., 2009. "Addressing imperfect maintenance modelling uncertainty in unavailability and cost based optimization," Reliability Engineering and System Safety, Elsevier, vol. 94(1), pages 22-32.
    6. Torres-Echeverría, A.C. & Martorell, S. & Thompson, H.A., 2009. "Modelling and optimization of proof testing policies for safety instrumented systems," Reliability Engineering and System Safety, Elsevier, vol. 94(4), pages 838-854.
    7. Caballé, N.C. & Castro, I.T. & Pérez, C.J. & Lanza-Gutiérrez, J.M., 2015. "A condition-based maintenance of a dependent degradation-threshold-shock model in a system with multiple degradation processes," Reliability Engineering and System Safety, Elsevier, vol. 134(C), pages 98-109.
    8. Shin, Sung Min & Jeon, In Seop & Kang, Hyun Gook, 2015. "Surveillance test and monitoring strategy for the availability improvement of standby equipment using age-dependent model," Reliability Engineering and System Safety, Elsevier, vol. 135(C), pages 100-106.
    9. Zhang, Jian & Huang, Xiaoyan & Fang, Youtong & Zhou, Jing & Zhang, He & Li, Jing, 2016. "Optimal inspection-based preventive maintenance policy for three-state mechanical components under competing failure modes," Reliability Engineering and System Safety, Elsevier, vol. 152(C), pages 95-103.
    10. Martón, I. & Sánchez, A.I. & Martorell, S., 2015. "Ageing PSA incorporating effectiveness of maintenance and testing," Reliability Engineering and System Safety, Elsevier, vol. 139(C), pages 131-140.
    Full references (including those not matched with items on IDEAS)

    Citations

    Citations are extracted by the CitEc Project, subscribe to its RSS feed for this item.
    as


    Cited by:

    1. Srivastav, Himanshu & Barros, Anne & Lundteigen, Mary Ann, 2020. "Modelling framework for performance analysis of SIS subject to degradation due to proof tests," Reliability Engineering and System Safety, Elsevier, vol. 195(C).
    2. Martón, I. & Sánchez, A.I. & Carlos, S. & Mullor, R. & Martorell, S., 2023. "Prognosis of wear-out effect on of safety equipment reliability for nuclear power plants long-term safe operation," Reliability Engineering and System Safety, Elsevier, vol. 233(C).
    3. Wu, Shaomin & Do, Phuc, 2017. "Editorial," Reliability Engineering and System Safety, Elsevier, vol. 168(C), pages 1-3.
    4. Zhang, Aibo & Srivastav, Himanshu & Barros, Anne & Liu, Yiliu, 2021. "Study of testing and maintenance strategies for redundant final elements in SIS with imperfect detection of degraded state," Reliability Engineering and System Safety, Elsevier, vol. 209(C).
    5. Martorell, S. & Martón, I. & Sánchez, A. & Carlos, S., 2020. "Harmonisation of surveillance requirements and maintenance in a context of ageing and obsolescence based on reliability, availability and risk information," Reliability Engineering and System Safety, Elsevier, vol. 202(C).
    6. Srivastav, Himanshu & Lundteigen, Mary Ann & Barros, Anne, 2021. "Introduction of degradation modeling in qualification of the novel subsea technology," Reliability Engineering and System Safety, Elsevier, vol. 216(C).
    7. Lin, Zhixian & Tao, Longlong & Wang, Shaoxuan & Yong, Nuo & Xia, Dongqin & Wang, Jianye & Ge, Daochuan, 2024. "A subset simulation analysis framework for rapid reliability evaluation of series-parallel cold standby systems," Reliability Engineering and System Safety, Elsevier, vol. 241(C).
    8. Chen, Ying & Wang, Ze & Li, YingYi & Kang, Rui & Mosleh, Ali, 2018. "Reliability analysis of a cold-standby system considering the development stages and accumulations of failure mechanisms," Reliability Engineering and System Safety, Elsevier, vol. 180(C), pages 1-12.
    9. Thiago Lima de Barros & Rodrigo Sampaio Lopes, 2021. "Continuous improvement of imperfect maintenance actions in PAS and PAR models," Journal of Risk and Reliability, , vol. 235(5), pages 941-958, October.

    Most related items

    These are the items that most often cite the same works as this one and are cited by the same works as this one.
    1. KanÄ ev, DuÅ¡ko & Gjorgiev, Blaže & Volkanovski, Andrija & ÄŒepin, Marko, 2016. "Time-dependent unavailability of equipment in an ageing NPP: Sensitivity study of a developed model," Reliability Engineering and System Safety, Elsevier, vol. 148(C), pages 11-20.
    2. Martón, I. & Sánchez, A.I. & Carlos, S. & Mullor, R. & Martorell, S., 2023. "Prognosis of wear-out effect on of safety equipment reliability for nuclear power plants long-term safe operation," Reliability Engineering and System Safety, Elsevier, vol. 233(C).
    3. Thiago Lima de Barros & Rodrigo Sampaio Lopes, 2021. "Continuous improvement of imperfect maintenance actions in PAS and PAR models," Journal of Risk and Reliability, , vol. 235(5), pages 941-958, October.
    4. Martorell, S. & Martón, I. & Sánchez, A. & Carlos, S., 2020. "Harmonisation of surveillance requirements and maintenance in a context of ageing and obsolescence based on reliability, availability and risk information," Reliability Engineering and System Safety, Elsevier, vol. 202(C).
    5. de Jonge, Bram & Scarf, Philip A., 2020. "A review on maintenance optimization," European Journal of Operational Research, Elsevier, vol. 285(3), pages 805-824.
    6. Chang, Miaoxin & Huang, Xianzhen & Coolen, Frank P.A. & Coolen-Maturi, Tahani, 2021. "Reliability analysis for systems based on degradation rates and hard failure thresholds changing with degradation levels," Reliability Engineering and System Safety, Elsevier, vol. 216(C).
    7. Liu, Yiliu & Rausand, Marvin, 2016. "Proof-testing strategies induced by dangerous detected failures of safety-instrumented systems," Reliability Engineering and System Safety, Elsevier, vol. 145(C), pages 366-372.
    8. Martorell, S. & Villamizar, M. & Martón, I. & Villanueva, J.F. & Carlos, S. & Sánchez, A.I., 2014. "Evaluation of risk impact of changes to surveillance requirements addressing model and parameter uncertainties," Reliability Engineering and System Safety, Elsevier, vol. 126(C), pages 153-165.
    9. Meng, Huixing & Kloul, Leïla & Rauzy, Antoine, 2018. "Modeling patterns for reliability assessment of safety instrumented systems," Reliability Engineering and System Safety, Elsevier, vol. 180(C), pages 111-123.
    10. Kowal, Karol, 2022. "Lifetime reliability and availability simulation for the electrical system of HTTR coupled to the electricity-hydrogen cogeneration plant," Reliability Engineering and System Safety, Elsevier, vol. 223(C).
    11. Cheng, Yao & Wei, Yian & Liao, Haitao, 2022. "Optimal sampling-based sequential inspection and maintenance plans for a heterogeneous product with competing failure modes," Reliability Engineering and System Safety, Elsevier, vol. 218(PB).
    12. Longhi, Antonio Eduardo Bier & Pessoa, Artur Alves & Garcia, Pauli Adriano de Almada, 2015. "Multiobjective optimization of strategies for operation and testing of low-demand safety instrumented systems using a genetic algorithm and fault trees," Reliability Engineering and System Safety, Elsevier, vol. 142(C), pages 525-538.
    13. Wang, Jiantai & Longyan, Tan & Ma, Xiaobing & Gao, Kaiye & Jia, Heping & Yang, Li, 2023. "Prognosis-driven reliability analysis and replacement policy optimization for two-phase continuous degradation," Reliability Engineering and System Safety, Elsevier, vol. 230(C).
    14. Zhou, Xiaojun & Wu, Changjie & Li, Yanting & Xi, Lifeng, 2016. "A preventive maintenance model for leased equipment subject to internal degradation and external shock damage," Reliability Engineering and System Safety, Elsevier, vol. 154(C), pages 1-7.
    15. Gabriel, Angelito & Ozansoy, Cagil & Shi, Juan, 2018. "Developments in SIL determination and calculation," Reliability Engineering and System Safety, Elsevier, vol. 177(C), pages 148-161.
    16. Martón, I. & Sánchez, A.I. & Martorell, S., 2015. "Ageing PSA incorporating effectiveness of maintenance and testing," Reliability Engineering and System Safety, Elsevier, vol. 139(C), pages 131-140.
    17. Zhang, Aibo & Hao, Songhua & Li, Peng & Xie, Min & Liu, Yiliu, 2022. "Performance modeling for condition-based activation of the redundant safety system subject to harmful tests," Reliability Engineering and System Safety, Elsevier, vol. 226(C).
    18. Torres-Echeverría, A.C. & Martorell, S. & Thompson, H.A., 2012. "Multi-objective optimization of design and testing of safety instrumented systems with MooN voting architectures using a genetic algorithm," Reliability Engineering and System Safety, Elsevier, vol. 106(C), pages 45-60.
    19. KanÄ ev, DuÅ¡ko & ÄŒepin, Marko & Gjorgiev, Blaže, 2014. "Development and application of a living probabilistic safety assessment tool: Multi-objective multi-dimensional optimization of surveillance requirements in NPPs considering their ageing," Reliability Engineering and System Safety, Elsevier, vol. 131(C), pages 135-147.
    20. Mechri, Walid & Simon, Christophe & BenOthman, Kamel, 2015. "Switching Markov chains for a holistic modeling of SIS unavailability," Reliability Engineering and System Safety, Elsevier, vol. 133(C), pages 212-222.

    Corrections

    All material on this site has been provided by the respective publishers and authors. You can help correct errors and omissions. When requesting a correction, please mention this item's handle: RePEc:eee:reensy:v:168:y:2017:i:c:p:18-27. See general information about how to correct material in RePEc.

    If you have authored this item and are not yet registered with RePEc, we encourage you to do it here. This allows to link your profile to this item. It also allows you to accept potential citations to this item that we are uncertain about.

    If CitEc recognized a bibliographic reference but did not link an item in RePEc to it, you can help with this form .

    If you know of missing items citing this one, you can help us creating those links by adding the relevant references in the same way as above, for each refering item. If you are a registered author of this item, you may also want to check the "citations" tab in your RePEc Author Service profile, as there may be some citations waiting for confirmation.

    For technical questions regarding this item, or to correct its authors, title, abstract, bibliographic or download information, contact: Catherine Liu (email available below). General contact details of provider: https://www.journals.elsevier.com/reliability-engineering-and-system-safety .

    Please note that corrections may take a couple of weeks to filter through the various RePEc services.

    IDEAS is a RePEc service. RePEc uses bibliographic data supplied by the respective publishers.