IDEAS home Printed from https://ideas.repec.org/a/eee/appene/v252y2019ic10.html
   My bibliography  Save this article

Three-dimensional CFD modelling and thermal performance analysis of porous volumetric receivers coupled to solar concentration systems

Author

Listed:
  • Barreto, Germilly
  • Canhoto, Paulo
  • Collares-Pereira, Manuel

Abstract

Porous volumetric receivers is a promising technology to improve the thermal performance of a new generation of concentrated solar power (CSP) plants. In this sense, this work addresses the Computational Fluid Dynamics (CFD) modelling and thermal performance analysis of porous volumetric receivers coupled to solar concentration systems. A cylindrical receiver element made of open-cell SiC ceramic foam was considered. The fluid flow and heat transfer processes in the porous media are modelled through volume averaged mass, momentum and energy conservation equations, considering the local thermal non-equilibrium (LTNE) approach, while the thermal radiation transfer is described by the P1 spherical harmonics method, using an open source software (OpenFOAM). An in-house algorithm based on the Monte Carlo Ray Tracing (MCRT) method was developed and coupled to the CFD mesh to model the propagation and absorption of solar radiation. The modelling of the receiver boundary conditions were improved, and a detailed analysis of a reference configuration of the receiver was conducted using a parabolic dish with a concentration ratio of 500 to generate the concentrated solar radiation field and a receiver element with diameter 5 cm, height 5 cm, pore size 3 mm and porosity 0.9. The thermal power output, thermal efficiency, mean fluid temperature at the outlet and pressure drop of this reference configuration are 628.92 W, 85.46%,474.22 K and 103.10 Pa, respectively. The use of receivers with high porosity and pores size increases the thermal efficiency slightly and decreases the pressure drop substantially. The convergent incidence of solar rays at the inlet of the receiver leads to high peaks of temperature in the porous structure and fluid, and a way to decrease these peaks is to design the concentration system or place the receiver in such way to obtain lower incidence angles at the inlet.

Suggested Citation

  • Barreto, Germilly & Canhoto, Paulo & Collares-Pereira, Manuel, 2019. "Three-dimensional CFD modelling and thermal performance analysis of porous volumetric receivers coupled to solar concentration systems," Applied Energy, Elsevier, vol. 252(C), pages 1-1.
  • Handle: RePEc:eee:appene:v:252:y:2019:i:c:10
    DOI: 10.1016/j.apenergy.2019.113433
    as

    Download full text from publisher

    File URL: http://www.sciencedirect.com/science/article/pii/S0306261919311079
    Download Restriction: Full text for ScienceDirect subscribers only

    File URL: https://libkey.io/10.1016/j.apenergy.2019.113433?utm_source=ideas
    LibKey link: if access is restricted and if your library uses this service, LibKey will redirect you to where you can use your library subscription to access this item
    ---><---

    As the access to this document is restricted, you may want to search for a different version of it.

    References listed on IDEAS

    as
    1. Du, Shen & Ren, Qinlong & He, Ya-Ling, 2017. "Optical and radiative properties analysis and optimization study of the gradually-varied volumetric solar receiver," Applied Energy, Elsevier, vol. 207(C), pages 27-35.
    2. Gomez-Garcia, Fabrisio & González-Aguilar, José & Olalde, Gabriel & Romero, Manuel, 2016. "Thermal and hydrodynamic behavior of ceramic volumetric absorbers for central receiver solar power plants: A review," Renewable and Sustainable Energy Reviews, Elsevier, vol. 57(C), pages 648-658.
    3. Zaversky, Fritz & Aldaz, Leticia & Sánchez, Marcelino & Ávila-Marín, Antonio L. & Roldán, M. Isabel & Fernández-Reche, Jesús & Füssel, Alexander & Beckert, Wieland & Adler, Jörg, 2018. "Numerical and experimental evaluation and optimization of ceramic foam as solar absorber – Single-layer vs multi-layer configurations," Applied Energy, Elsevier, vol. 210(C), pages 351-375.
    4. Du, Shen & Li, Ming-Jia & Ren, Qinlong & Liang, Qi & He, Ya-Ling, 2017. "Pore-scale numerical simulation of fully coupled heat transfer process in porous volumetric solar receiver," Energy, Elsevier, vol. 140(P1), pages 1267-1275.
    5. Cui, F.Q. & He, Y.L. & Cheng, Z.D. & Li, D. & Tao, Y.B., 2012. "Numerical simulations of the solar transmission process for a pressurized volumetric receiver," Energy, Elsevier, vol. 46(1), pages 618-628.
    6. Chen, Xue & Wang, Fuqiang & Yan, Xuewei & Han, Yafen & Cheng, Ziming & Jie, Zhu, 2018. "Thermochemical performance of solar driven CO2 reforming of methane in volumetric reactor with gradual foam structure," Energy, Elsevier, vol. 151(C), pages 545-555.
    7. Wu, Zhiyong & Caliot, Cyril & Bai, Fengwu & Flamant, Gilles & Wang, Zhifeng & Zhang, Jinsong & Tian, Chong, 2010. "Experimental and numerical studies of the pressure drop in ceramic foams for volumetric solar receiver applications," Applied Energy, Elsevier, vol. 87(2), pages 504-513, February.
    8. Avila-Marin, A.L. & Fernandez-Reche, J. & Martinez-Tarifa, A., 2019. "Modelling strategies for porous structures as solar receivers in central receiver systems: A review," Renewable and Sustainable Energy Reviews, Elsevier, vol. 111(C), pages 15-33.
    9. Ho, Clifford K. & Iverson, Brian D., 2014. "Review of high-temperature central receiver designs for concentrating solar power," Renewable and Sustainable Energy Reviews, Elsevier, vol. 29(C), pages 835-846.
    10. Barreto, Germilly & Canhoto, Paulo & Collares-Pereira, Manuel, 2018. "Three-dimensional modelling and analysis of solar radiation absorption in porous volumetric receivers," Applied Energy, Elsevier, vol. 215(C), pages 602-614.
    11. Nimvari, Majid Eshagh & Jouybari, Nima Fallah & Esmaili, Qadir, 2018. "A new approach to mitigate intense temperature gradients in ceramic foam solar receivers," Renewable Energy, Elsevier, vol. 122(C), pages 206-215.
    12. Du, Shen & Tong, Zi-Xiang & Zhang, Hong-Hu & He, Ya-Ling, 2019. "Tomography-based determination of Nusselt number correlation for the porous volumetric solar receiver with different geometrical parameters," Renewable Energy, Elsevier, vol. 135(C), pages 711-718.
    13. Capuano, Raffaele & Fend, Thomas & Schwarzbözl, Peter & Smirnova, Olena & Stadler, Hannes & Hoffschmidt, Bernhard & Pitz-Paal, Robert, 2016. "Numerical models of advanced ceramic absorbers for volumetric solar receivers," Renewable and Sustainable Energy Reviews, Elsevier, vol. 58(C), pages 656-665.
    Full references (including those not matched with items on IDEAS)

    Citations

    Citations are extracted by the CitEc Project, subscribe to its RSS feed for this item.
    as


    Cited by:

    1. Hongyan Lu & Lixin Yang & Zhiyong Wu & Siqi Xu, 2020. "Numerical and Experimental Study on Convective Heat Transfer Characteristics in Foam Materials," Energies, MDPI, vol. 13(2), pages 1-14, January.
    2. Sedighi, Mohammadreza & Padilla, Ricardo Vasquez & Alamdari, Pedram & Lake, Maree & Rose, Andrew & Izadgoshasb, Iman & Taylor, Robert A., 2020. "A novel high-temperature (>700 °C), volumetric receiver with a packed bed of transparent and absorbing spheres," Applied Energy, Elsevier, vol. 264(C).
    3. Navalho, Jorge E.P. & Pereira, José C.F., 2020. "A comprehensive and fully predictive discrete methodology for volumetric solar receivers: application to a functional parabolic dish solar collector system," Applied Energy, Elsevier, vol. 267(C).
    4. Guilong Dai & Jiangfei Huangfu & Xiaoyu Wang & Shenghua Du & Tian Zhao, 2023. "A Review of Radiative Heat Transfer in Fixed-Bed Particle Solar Receivers," Sustainability, MDPI, vol. 15(13), pages 1-37, June.
    5. Wang, P. & Li, J.B. & Xu, R.N. & Jiang, P.X., 2021. "Non-uniform and volumetric effect on the hydrodynamic and thermal characteristic in a unit solar absorber," Energy, Elsevier, vol. 225(C).
    6. Barreto, Germilly & Canhoto, Paulo & Collares-Pereira, Manuel, 2020. "Parametric analysis and optimisation of porous volumetric solar receivers made of open-cell SiC ceramic foam," Energy, Elsevier, vol. 200(C).
    7. Xu, Hong & Yu, Wenhui & Zhang, Yuan & Ma, Suli & Wu, Zhiyuan & Liu, Xiaohu, 2023. "Flow and heat transfer performance of bionic heat transfer structures with hybrid triply periodic minimal surfaces," Applied Energy, Elsevier, vol. 351(C).
    8. Siavashi, Majid & Hosseini, Farzad & Talesh Bahrami, Hamid Reza, 2021. "A new design with preheating and layered porous ceramic for hydrogen production through methane steam reforming process," Energy, Elsevier, vol. 231(C).
    9. Guilong Dai & Ying Zhuang & Xiaoyu Wang & Xue Chen & Chuang Sun & Shenghua Du, 2022. "Experimental Investigation on the Vector Characteristics of Concentrated Solar Radiation Flux Map," Energies, MDPI, vol. 16(1), pages 1-15, December.
    10. Pratticò, Luca & Fronza, Nicola & Bartali, Ruben & Chiappini, Andrea & Sciubba, Enrico & González-Aguilar, J. & Crema, Luigi, 2021. "Radiation propagation in a hierarchical solar volumetric absorber: Results of single-photon avalanche diode measurements and Monte Carlo ray tracing analysis," Renewable Energy, Elsevier, vol. 180(C), pages 482-493.
    11. Zhang, Hao & Shuai, Yong & Lougou, Bachirou Guene & Jiang, Boshu & Yang, Dazhi & Pan, Qinghui & Wang, Fuqiang & Huang, Xing, 2022. "Effects of foam structure on thermochemical characteristics of porous-filled solar reactor," Energy, Elsevier, vol. 239(PC).
    12. Godini, Ali & Kheradmand, Saeid, 2021. "Optimization of volumetric solar receiver geometry and porous media specifications," Renewable Energy, Elsevier, vol. 172(C), pages 574-581.

    Most related items

    These are the items that most often cite the same works as this one and are cited by the same works as this one.
    1. Navalho, Jorge E.P. & Pereira, José C.F., 2020. "A comprehensive and fully predictive discrete methodology for volumetric solar receivers: application to a functional parabolic dish solar collector system," Applied Energy, Elsevier, vol. 267(C).
    2. Avila-Marin, A.L. & Fernandez-Reche, J. & Martinez-Tarifa, A., 2019. "Modelling strategies for porous structures as solar receivers in central receiver systems: A review," Renewable and Sustainable Energy Reviews, Elsevier, vol. 111(C), pages 15-33.
    3. Barreto, Germilly & Canhoto, Paulo & Collares-Pereira, Manuel, 2020. "Parametric analysis and optimisation of porous volumetric solar receivers made of open-cell SiC ceramic foam," Energy, Elsevier, vol. 200(C).
    4. Barreto, Germilly & Canhoto, Paulo & Collares-Pereira, Manuel, 2018. "Three-dimensional modelling and analysis of solar radiation absorption in porous volumetric receivers," Applied Energy, Elsevier, vol. 215(C), pages 602-614.
    5. Carlos E. Arreola-Ramos & Omar Álvarez-Brito & Juan Daniel Macías & Aldo Javier Guadarrama-Mendoza & Manuel A. Ramírez-Cabrera & Armando Rojas-Morin & Patricio J. Valadés-Pelayo & Heidi Isabel Villafá, 2021. "Experimental Evaluation and Modeling of Air Heating in a Ceramic Foam Volumetric Absorber by Effective Parameters," Energies, MDPI, vol. 14(9), pages 1-15, April.
    6. Guilong Dai & Jiangfei Huangfu & Xiaoyu Wang & Shenghua Du & Tian Zhao, 2023. "A Review of Radiative Heat Transfer in Fixed-Bed Particle Solar Receivers," Sustainability, MDPI, vol. 15(13), pages 1-37, June.
    7. Zhu, Qibin & Xuan, Yimin, 2019. "Improving the performance of volumetric solar receivers with a spectrally selective gradual structure and swirling characteristics," Energy, Elsevier, vol. 172(C), pages 467-476.
    8. Sedighi, Mohammadreza & Padilla, Ricardo Vasquez & Alamdari, Pedram & Lake, Maree & Rose, Andrew & Izadgoshasb, Iman & Taylor, Robert A., 2020. "A novel high-temperature (>700 °C), volumetric receiver with a packed bed of transparent and absorbing spheres," Applied Energy, Elsevier, vol. 264(C).
    9. Avila-Marin, Antonio L. & Fernandez-Reche, Jesus & Carballo, Jose Antonio & Carra, Maria Elena & Gianella, Sandro & Ferrari, Luca & Sanchez-Señoran, Daniel, 2022. "CFD analysis of the performance impact of geometrical shape on volumetric absorbers in a standard cup," Renewable Energy, Elsevier, vol. 201(P1), pages 256-272.
    10. Avila-Marin, Antonio L. & Fernandez-Reche, Jesus & Gianella, Sandro & Ferrari, Luca & Sanchez-Señoran, Daniel, 2022. "Experimental study of innovative periodic cellular structures as air volumetric absorbers," Renewable Energy, Elsevier, vol. 184(C), pages 391-404.
    11. Li, J.B. & Wang, P. & Liu, D.Y., 2022. "Optimization on the gradually varied pore structure distribution for the irradiated absorber," Energy, Elsevier, vol. 240(C).
    12. Du, Shen & Li, Ming-Jia & He, Ya-Ling & Shen, Sheng, 2021. "Conceptual design of porous volumetric solar receiver using molten salt as heat transfer fluid," Applied Energy, Elsevier, vol. 301(C).
    13. Pitot de la Beaujardiere, Jean-Francois P. & Reuter, Hanno C.R., 2018. "A review of performance modelling studies associated with open volumetric receiver CSP plant technology," Renewable and Sustainable Energy Reviews, Elsevier, vol. 82(P3), pages 3848-3862.
    14. Avila-Marin, Antonio L., 2022. "CFD parametric analysis of wire meshes open volumetric receivers with axial-varied porosity and comparison with small-scale solar receiver tests," Renewable Energy, Elsevier, vol. 193(C), pages 1094-1105.
    15. Du, Shen & Xia, Tian & He, Ya-Ling & Li, Zeng-Yao & Li, Dong & Xie, Xiang-Qian, 2020. "Experiment and optimization study on the radial graded porous volumetric solar receiver matching non-uniform solar flux distribution," Applied Energy, Elsevier, vol. 275(C).
    16. Huang, Haodong & Lin, Meng, 2021. "Optimization of solar receivers for high-temperature solar conversion processes: Direct vs. Indirect illumination designs," Applied Energy, Elsevier, vol. 304(C).
    17. Du, Shen & Tong, Zi-Xiang & Zhang, Hong-Hu & He, Ya-Ling, 2019. "Tomography-based determination of Nusselt number correlation for the porous volumetric solar receiver with different geometrical parameters," Renewable Energy, Elsevier, vol. 135(C), pages 711-718.
    18. Akba, Tufan & Baker, Derek & Mengüç, M. Pınar, 2023. "Gradient-based optimization of micro-scale pressurized volumetric receiver geometry and flow rate," Renewable Energy, Elsevier, vol. 203(C), pages 741-752.
    19. Zhang, Hao & Shuai, Yong & Lougou, Bachirou Guene & Jiang, Boshu & Yang, Dazhi & Pan, Qinghui & Wang, Fuqiang & Huang, Xing, 2022. "Effects of foam structure on thermochemical characteristics of porous-filled solar reactor," Energy, Elsevier, vol. 239(PC).
    20. Wang, P. & Li, J.B. & Zhou, L. & Liu, D.Y., 2020. "Acceptance-Rejection Sampling Based Monte Carlo Ray Tracing in Anisotropic Porous Media," Energy, Elsevier, vol. 199(C).

    Corrections

    All material on this site has been provided by the respective publishers and authors. You can help correct errors and omissions. When requesting a correction, please mention this item's handle: RePEc:eee:appene:v:252:y:2019:i:c:10. See general information about how to correct material in RePEc.

    If you have authored this item and are not yet registered with RePEc, we encourage you to do it here. This allows to link your profile to this item. It also allows you to accept potential citations to this item that we are uncertain about.

    If CitEc recognized a bibliographic reference but did not link an item in RePEc to it, you can help with this form .

    If you know of missing items citing this one, you can help us creating those links by adding the relevant references in the same way as above, for each refering item. If you are a registered author of this item, you may also want to check the "citations" tab in your RePEc Author Service profile, as there may be some citations waiting for confirmation.

    For technical questions regarding this item, or to correct its authors, title, abstract, bibliographic or download information, contact: Catherine Liu (email available below). General contact details of provider: http://www.elsevier.com/wps/find/journaldescription.cws_home/405891/description#description .

    Please note that corrections may take a couple of weeks to filter through the various RePEc services.

    IDEAS is a RePEc service. RePEc uses bibliographic data supplied by the respective publishers.