IDEAS home Printed from https://ideas.repec.org/a/gam/jsusta/v15y2023i5p4559-d1086998.html
   My bibliography  Save this article

Effects of Pre-Turbocharger Turbine Water Injection on the Sustainable Performance of Spark Ignition Engine

Author

Listed:
  • Ibham Veza

    (Department of Mechanical Engineering, Universiti Teknologi PETRONAS, Seri Iskandar 32610, Malaysia)

  • Ling Chee Huat

    (Automotive Development Centre, Institute for Vehicle Systems and Engineering, Universiti Teknologi Malaysia, Johor Bahru 81310, Malaysia)

  • Mohd Azman Abas

    (Automotive Development Centre, Institute for Vehicle Systems and Engineering, Universiti Teknologi Malaysia, Johor Bahru 81310, Malaysia)

  • Muhammad Idris

    (School of Environmental Science, University of Indonesia, Jakarta 10430, Indonesia)

  • Martin Spraggon

    (Research & Innovation Center Division, Rabdan Academy, Abu Dhabi P.O. Box 114646, United Arab Emirates)

  • Safarudin G. Herawan

    (Industrial Engineering Department, Faculty of Engineering, Bina Nusantara University, Jakarta 11480, Indonesia)

Abstract

Water injection strategy is considered a promising technique to improve the performance of boosted engine and reduce the NOx emission via the latent heat of water vaporization. Numerous research on water injection has been conducted on in-cylinder and intake port water injection. However, the water injection focusing on the spark ignition (SI) engine exhaust system is still lacking. This study proposed a pre-turbocharger turbine water injection (PTWI) concept to reduce the turbine inlet temperature. This was done so that the stoichiometric engine operation could be achieved at a medium–high load and engine speed without resorting to a fuel enrichment strategy to reduce the exhaust gas temperature. This study aims to investigate the effect of injecting water into the exhaust gas at the pre-turbine of a turbocharged spark ignition engine. This study experimented on a 1.3-L 4-cylinder turbocharged engine to collect engine data for computational fluid dynamics (CFD) baseline model validation. A one-dimensional engine model was then developed based on the 1.6-L 4-cylinder turbocharged engine experiment using AVL BOOST software. The CFD model was used to investigate the effects of water injection pressure, pipe diameter, and water injector location. The CFD results showed that a 50 mm connecting pipe with 4 bar of injection pressure gives the largest reduction in exhaust temperature. The CFD results were then applied to the one-dimensional engine model. The engine model simulation results showed that the fuel consumption could be reduced up to 13% at 4000 rpm during wide-open throttle and 75% engine load. The PTWI is a new approach, but this study has proved the potential of using water injection at the pre-turbine turbocharger to reduce the fuel consumption of a turbocharged SI engine.

Suggested Citation

  • Ibham Veza & Ling Chee Huat & Mohd Azman Abas & Muhammad Idris & Martin Spraggon & Safarudin G. Herawan, 2023. "Effects of Pre-Turbocharger Turbine Water Injection on the Sustainable Performance of Spark Ignition Engine," Sustainability, MDPI, vol. 15(5), pages 1-36, March.
    • Handle: RePEc:gam:jsusta:v:15:y:2023:i:5:p:4559-:d:1086998
    as

    Download full text from publisher

    File URL: https://www.mdpi.com/2071-1050/15/5/4559/pdf
    Download Restriction: no
    File URL: https://www.mdpi.com/2071-1050/15/5/4559/
    Download Restriction: no
    ---><---

    References listed on IDEAS

    as
    1. De Cuyper, Thomas & Demuynck, Joachim & Broekaert, Stijn & De Paepe, Michel & Verhelst, Sebastian, 2016. "Heat transfer in premixed spark ignition engines part II: Systematic analysis of the heat transfer phenomena," Energy, Elsevier, vol. 116(P1), pages 851-860.
    2. Bozza, Fabio & De Bellis, Vincenzo & Teodosio, Luigi, 2016. "Potentials of cooled EGR and water injection for knock resistance and fuel consumption improvements of gasoline engines," Applied Energy, Elsevier, vol. 169(C), pages 112-125.
    3. Broekaert, Stijn & Demuynck, Joachim & De Cuyper, Thomas & De Paepe, Michel & Verhelst, Sebastian, 2016. "Heat transfer in premixed spark ignition engines part I: Identification of the factors influencing heat transfer," Energy, Elsevier, vol. 116(P1), pages 380-391.
    Full references (including those not matched with items on IDEAS)

    Most related items

    These are the items that most often cite the same works as this one and are cited by the same works as this one.
    1. Broekaert, Stijn & De Cuyper, Thomas & De Paepe, Michel & Verhelst, Sebastian, 2016. "Experimental investigation of the effect of engine settings on the wall heat flux during HCCI combustion," Energy, Elsevier, vol. 116(P1), pages 1077-1086.
    2. Decan, Gilles & Broekaert, Stijn & Lucchini, Tommaso & D’Errico, Gianluca & Vierendeels, Jan & Verhelst, Sebastian, 2018. "Evaluation of wall heat flux calculation methods for CFD simulations of an internal combustion engine under both motored and HCCI operation," Applied Energy, Elsevier, vol. 232(C), pages 451-461.
    3. Serrano, José Ramón & Piqueras, Pedro & De la Morena, Joaquín & Gómez-Vilanova, Alejandro & Guilain, Stéphane, 2021. "Methodological analysis of variable geometry turbine technology impact on the performance of highly downsized spark-ignition engines," Energy, Elsevier, vol. 215(PB).
    4. Karthic, S.V. & Senthil Kumar, M., 2021. "Experimental investigations on hydrogen biofueled reactivity controlled compression ignition engine using open ECU," Energy, Elsevier, vol. 229(C).
    5. Jacopo Zembi & Michele Battistoni & Francesco Ranuzzi & Nicolò Cavina & Matteo De Cesare, 2019. "CFD Analysis of Port Water Injection in a GDI Engine under Incipient Knock Conditions," Energies, MDPI, vol. 12(18), pages 1-22, September.
    6. Duan, Xiongbo & Liu, Jingping & Yao, Jun & Chen, Zheng & Wu, Cheng & Chen, Ceyuan & Dong, Hao, 2018. "Performance, combustion and knock assessment of a high compression ratio and lean-burn heavy-duty spark-ignition engine fuelled with n-butane and liquefied methane gas blend," Energy, Elsevier, vol. 158(C), pages 256-268.
    7. Thiago Rodrigo Vieira da Silva & Nilton Antonio Diniz Netto & Jeanine Costa Santos & Augusto Cesar Teixeira Malaquias & José Guilherme Coelho Baêta, 2022. "Development Procedure for Performance Estimation and Main Dimensions Calculation of a Highly-Boosted Ethanol Engine with Water Injection," Energies, MDPI, vol. 15(13), pages 1-24, June.
    8. Miganakallu, Niranjan & Yang, Zhuyong & Rogóż, Rafał & Kapusta, Łukasz Jan & Christensen, Cord & Barros, Sam & Naber, Jeffrey, 2020. "Effect of water - methanol blends on engine performance at borderline knock conditions in gasoline direct injection engines," Applied Energy, Elsevier, vol. 264(C).
    9. Landry Frank Ineza Havugimana & Bolan Liu & Fanshuo Liu & Junwei Zhang & Ben Li & Peng Wan, 2023. "Review of Artificial Intelligent Algorithms for Engine Performance, Control, and Diagnosis," Energies, MDPI, vol. 16(3), pages 1-25, January.
    10. Rocha, Déborah Domingos da & de Castro Radicchi, Fábio & Lopes, Gustavo Santos & Brunocilla, Marcello Francisco & Gomes, Paulo César de Ferreira & Santos, Nathalia Duarte Souza Alvarenga & Malaquias, , 2021. "Study of the water injection control parameters on combustion performance of a spark-ignition engine," Energy, Elsevier, vol. 217(C).
    11. Xu, Han & Gao, Jian & Yao, Anren & Yao, Chunde, 2018. "The effect of the energy convergence and energy dissipation on the formation of severe knock," Applied Energy, Elsevier, vol. 228(C), pages 1243-1254.
    12. Zhao, Rongchao & Li, Weihua & Zhuge, Weilin & Zhang, Yangjun & Yin, Yong, 2017. "Numerical study on steam injection in a turbocompound diesel engine for waste heat recovery," Applied Energy, Elsevier, vol. 185(P1), pages 506-518.
    13. Nguyen Xuan Khoa & Ocktaeck Lim, 2022. "A Review of the External and Internal Residual Exhaust Gas in the Internal Combustion Engine," Energies, MDPI, vol. 15(3), pages 1-21, February.
    14. Discepoli, G. & Cruccolini, V. & Ricci, F. & Di Giuseppe, A. & Papi, S. & Grimaldi, C.N., 2020. "Experimental characterisation of the thermal energy released by a Radio-Frequency Corona Igniter in nitrogen and air," Applied Energy, Elsevier, vol. 263(C).
    15. Xu, Han & Yao, Anren & Yao, Chunde & Gao, Jian, 2017. "Investigation of energy transformation and damage effect under severe knock of engines," Applied Energy, Elsevier, vol. 203(C), pages 506-521.
    16. Zhang, Qinghui & Hao, Zhiyong & Zheng, Xu & Yang, Wenying, 2017. "Characteristics and effect factors of pressure oscillation in multi-injection DI diesel engine at high-load conditions," Applied Energy, Elsevier, vol. 195(C), pages 52-66.
    17. De Cuyper, Thomas & Demuynck, Joachim & Broekaert, Stijn & De Paepe, Michel & Verhelst, Sebastian, 2016. "Heat transfer in premixed spark ignition engines part II: Systematic analysis of the heat transfer phenomena," Energy, Elsevier, vol. 116(P1), pages 851-860.
    18. Broekaert, Stijn & De Cuyper, Thomas & De Paepe, Michel & Verhelst, Sebastian, 2017. "Evaluation of empirical heat transfer models for HCCI combustion in a CFR engine," Applied Energy, Elsevier, vol. 205(C), pages 1141-1150.
    19. Zhao, Jinxing, 2017. "Research and application of over-expansion cycle (Atkinson and Miller) engines – A review," Applied Energy, Elsevier, vol. 185(P1), pages 300-319.
    20. Duan, Xiongbo & Liu, Jingping & Yuan, Zhipeng & Guo, Genmiao & Liu, Qi & Tang, Qijun & Deng, Banglin & Guan, Jinhuan, 2018. "Experimental investigation of the effects of injection strategies on cycle-to-cycle variations of a DISI engine fueled with ethanol and gasoline blend," Energy, Elsevier, vol. 165(PB), pages 455-470.

    Corrections

    All material on this site has been provided by the respective publishers and authors. You can help correct errors and omissions. When requesting a correction, please mention this item's handle: RePEc:gam:jsusta:v:15:y:2023:i:5:p:4559-:d:1086998. See general information about how to correct material in RePEc.

    If you have authored this item and are not yet registered with RePEc, we encourage you to do it here. This allows to link your profile to this item. It also allows you to accept potential citations to this item that we are uncertain about.

    If CitEc recognized a bibliographic reference but did not link an item in RePEc to it, you can help with this form .

    If you know of missing items citing this one, you can help us creating those links by adding the relevant references in the same way as above, for each refering item. If you are a registered author of this item, you may also want to check the "citations" tab in your RePEc Author Service profile, as there may be some citations waiting for confirmation.

    For technical questions regarding this item, or to correct its authors, title, abstract, bibliographic or download information, contact: MDPI Indexing Manager (email available below). General contact details of provider: https://www.mdpi.com .

    Please note that corrections may take a couple of weeks to filter through the various RePEc services.

    IDEAS is a RePEc service. RePEc uses bibliographic data supplied by the respective publishers.