IDEAS home Printed from https://ideas.repec.org/a/apa/ijtess/2017p177-183.html
   My bibliography  Save this article

The Design and Mechanical Analysis of Double Zigzag Type of Adhesive Joints

Author

Listed:
  • BAHADIR BIRECIKLI

    (Firat University, Elazig, Turkey)

  • AYDIN TURGUT

    (Bingol University, Bingol, Turkey)

Abstract

In this article, the mechanical analysis of double zigzag type of adhesive joints was investigated. Glass-fibre prepregs adherends examined on several overlap angles under axial tensile loading. Overlap angle, 30o, 45o, 60o, and 75o were employed. Ductile-type epoxy adhesive was employed for bonding area. The effect of overlap angles on zigzag type of joints was studied as numerical and experimental separately. For numerical process, three-dimensional finite element analysis was exercised to understand the stress distributions in the bonding area by ANSYS⃝R 14.5 version. Failure criteria Von Mises Equivalent Stress can acceptably determine close by experimental results for joint strength. The failure load of overlap angle joints is directly proportional as it increases as the overlap angle increases. Furthermore, the available experimental results perfectly match with numerical results.

Suggested Citation

  • Bahadir Birecikli & Aydin Turgut, 2017. "The Design and Mechanical Analysis of Double Zigzag Type of Adhesive Joints," International Journal of Technology and Engineering Studies, PROF.IR.DR.Mohid Jailani Mohd Nor, vol. 3(5), pages 177-183.
    • Handle: RePEc:apa:ijtess:2017:p:177-183
    DOI: 10.20469/ijtes.3.40001-5
    as

    Download full text from publisher

    File URL: https://kkgpublications.com/technology-engineering-studies-volume-3-issue-5/
    Download Restriction: no
    File URL: https://kkgpublications.com/wp-content/uploads/2018/09/ijtes.3.40001.5.pdf
    Download Restriction: no
    File URL: https://libkey.io/10.20469/ijtes.3.40001-5?utm_source=ideas
    LibKey link: if access is restricted and if your library uses this service, LibKey will redirect you to where you can use your library subscription to access this item
    ---><---

    References listed on IDEAS

    as
    1. Jeeyoung Lim & Liu Yue & Youngju Na & Sunkuk Kim, 2016. "Four cases of production-installation simulation for free-form concrete panels," Journal of Advances in Technology and Engineering Research, A/Professor Akbar A. Khatibi, vol. 2(1), pages 22-27.
    2. Jae-Hoon Lee & Si-Pom Kim & Rock-Won Jeon, 2016. "Optimal design for adiabatic pipes using vacuum at cryogenic temperatures," Journal of Advances in Technology and Engineering Research, A/Professor Akbar A. Khatibi, vol. 2(1), pages 06-11.
    Full references (including those not matched with items on IDEAS)

    Most related items

    These are the items that most often cite the same works as this one and are cited by the same works as this one.
    1. M. Syafwansyah Effendi & Noor Rahman & Ahmad Hendrawan, 2017. "The Use of Sollar Collector as Preheater and Condensate Pipe as Heat Recovery in Basin Solar Still to Increase Efficency," International Journal of Technology and Engineering Studies, PROF.IR.DR.Mohid Jailani Mohd Nor, vol. 3(6), pages 264-273.
    2. Mohamed A. Mohamed & Qin Ning, 2017. "The failure of delayed detached eddy simulation for flow control over a hump using synthetic jet actuator," Journal of Advances in Technology and Engineering Research, A/Professor Akbar A. Khatibi, vol. 3(5), pages 192-210.
    3. Fouzan Al Qaisi, 2019. "The Relationship Between Cash Flow and Profitability of Insurance Companies listed in Amman Stock Exchange in Jordan," The Journal of Social Sciences Research, Academic Research Publishing Group, vol. 5(1), pages 51-60, 01-2019.
    4. S. W. M. A. I. Senevirathne & R. K. P. S. Ranaweera, 2018. "Effects of cutting speed on tool nose wear with ACE-MQL aerosol at optimum-temperature," Journal of Advances in Technology and Engineering Research, A/Professor Akbar A. Khatibi, vol. 4(1), pages 27-36.
    5. Regina Lambin & Norwaliza Abdul Wahab & Goh Swee Choo & Ramlee Mustapha & Ramlee Abdullah, 2018. "An exploratory study on Indigenous Knowledge of ‘Green Technology’ (IKGT) among orang asli in Malaysia," Journal of Advances in Humanities and Social Sciences, Dr. Yi-Hsing Hsieh, vol. 4(4), pages 183-196.

    Corrections

    All material on this site has been provided by the respective publishers and authors. You can help correct errors and omissions. When requesting a correction, please mention this item's handle: RePEc:apa:ijtess:2017:p:177-183. See general information about how to correct material in RePEc.

    If you have authored this item and are not yet registered with RePEc, we encourage you to do it here. This allows to link your profile to this item. It also allows you to accept potential citations to this item that we are uncertain about.

    If CitEc recognized a bibliographic reference but did not link an item in RePEc to it, you can help with this form .

    If you know of missing items citing this one, you can help us creating those links by adding the relevant references in the same way as above, for each refering item. If you are a registered author of this item, you may also want to check the "citations" tab in your RePEc Author Service profile, as there may be some citations waiting for confirmation.

    For technical questions regarding this item, or to correct its authors, title, abstract, bibliographic or download information, contact: PROF.IR.DR.Mohid Jailani Mohd Nor (email available below). General contact details of provider: https://kkgpublications.com/technology/ .

    Please note that corrections may take a couple of weeks to filter through the various RePEc services.

    IDEAS is a RePEc service. RePEc uses bibliographic data supplied by the respective publishers.