IDEAS home Printed from https://ideas.repec.org/a/apa/ijtess/2016p101-109.html
   My bibliography  Save this article

Electricity-Generating Wind Turbine from Electric Bicycle Motor

Author

Listed:
  • NICHANNANT SEMSRI

    (Suan Sunandha Rajabhat University, Bangkok, Thailand)

  • CHONMAPAT TORASA

    (Suan Sunandha Rajabhat University, Bangkok, Thailand)

  • KITTIPAT SAMERJAI

    (Suan Sunandha Rajabhat University, Bangkok, Thailand)

  • MONTRIE SUKSOMBAT

    (Suan Sunandha Rajabhat University, Bangkok, Thailand)

  • PISIT SINPENG

    (Suan Sunandha Rajabhat University, Bangkok, Thailand)

Abstract

Wind energy is one type of renewable energy which does not cause pollution. Presently, there is a technological development to apply wind energy for the electricity generation. Wind energy is used to replace fossil energy, such as oil and coal, causing environmental pollution. In Thailand, the studies of wind energy application to generate electricity have been promoted. Nowadays, there is number of small and medium wind turbines used for electricity generation in buildings, houses and small communities. This project took a 48 volts, 1,000 watt electric bicycle motor to apply in order to make a saline county wind turbine to generate electricity. The turbine consisted of 6 rotor blades. Each blade was 1.5 meters long, and was made from 150 x 130 centimeter synthetic fabrics. A rotor of the turbine was connected with a rotor of the electric bicycle motor through a 1:7.5 gearbox to increase the rotational speed of the electric bicycle motor. From the experiment, it was found that the invented saline county wind turbine started rotating at the wind speed of 1.5 m/s and generated 3 phases of AC voltage. Average voltage in each phase was 6 volts at the rotational speed of 60-80 rpm. As seen from the test, at the maximum wind speed of 4.7 m/s, 11-12 volts of AC voltage in a single phase was produced with the approximate 130-140 rpm rotational speed of the motor. When connecting the generated AC voltage to rectifier and filter circuits to convert it into DC voltage for battery charging purpose, the maximum wind speed at 4.7 m/s generated approximately 15-16 volts of DC voltage. This capacity was sufficient for 12-volt battery charging in a real use.

Suggested Citation

  • Nichannant Semsri & Chonmapat Torasa & Kittipat Samerjai & Montrie Suksombat & Pisit Sinpeng, 2016. "Electricity-Generating Wind Turbine from Electric Bicycle Motor," International Journal of Technology and Engineering Studies, PROF.IR.DR.Mohid Jailani Mohd Nor, vol. 2(4), pages 101-109.
  • Handle: RePEc:apa:ijtess:2016:p:101-109
    DOI: 10.20469/ijtes.2.40002-4
    as

    Download full text from publisher

    File URL: https://kkgpublications.com/technology-engineering-studies-volume-2-issue-4/
    Download Restriction: no

    File URL: https://kkgpublications.com/wp-content/uploads/2019/04/ijtes.2.40002-4.pdf
    Download Restriction: no

    File URL: https://libkey.io/10.20469/ijtes.2.40002-4?utm_source=ideas
    LibKey link: if access is restricted and if your library uses this service, LibKey will redirect you to where you can use your library subscription to access this item
    ---><---

    Citations

    Citations are extracted by the CitEc Project, subscribe to its RSS feed for this item.
    as


    Cited by:

    1. Joni Dewanto & Oegik Soegihardjo, 2020. "Organizing Decision-Making Support System Based Multi-Dimensional Analysis of the Educational Process Data," Journal of ICT, Design, Engineering and Technological Science, Juhriyansyah Dalle, vol. 4(1), pages 6-11.
    2. S. Farrukh Haider & M. M. Quazi & Jahanzeb Bhatt & M Nasir Bashir & Imran Ali, 2019. "Effect of Shielded Metal Arc Welding (SMAW) parameters on mechanical properties of low-carbon, mild and stainless-steel welded joints: A review," Journal of Advances in Technology and Engineering Research, A/Professor Akbar A. Khatibi, vol. 5(5), pages 191-198.
    3. Yi-Chang Wu & Mi-Ching Tsai & Hao-Pin Wu, 2019. "Transmitted Torque Analysis of Coaxial Magnetic Gears with Different Pole-Pair Numbers," Journal of ICT, Design, Engineering and Technological Science, Juhriyansyah Dalle, vol. 3(1), pages 1-5.
    4. WooYoung Jung & Viriyavudh Sim & Jungkyu Choi, 2017. "Fragility assessment of the connection used in small-scale residential steel house subjected to lateral wind loads," Journal of Advances in Technology and Engineering Research, A/Professor Akbar A. Khatibi, vol. 3(3), pages 101-107.
    5. Tuka N Fattal, 2018. "Increasing Wind Turbine Efficiency," International Journal of Technology and Engineering Studies, PROF.IR.DR.Mohid Jailani Mohd Nor, vol. 4(4), pages 120-131.

    Corrections

    All material on this site has been provided by the respective publishers and authors. You can help correct errors and omissions. When requesting a correction, please mention this item's handle: RePEc:apa:ijtess:2016:p:101-109. See general information about how to correct material in RePEc.

    If you have authored this item and are not yet registered with RePEc, we encourage you to do it here. This allows to link your profile to this item. It also allows you to accept potential citations to this item that we are uncertain about.

    We have no bibliographic references for this item. You can help adding them by using this form .

    If you know of missing items citing this one, you can help us creating those links by adding the relevant references in the same way as above, for each refering item. If you are a registered author of this item, you may also want to check the "citations" tab in your RePEc Author Service profile, as there may be some citations waiting for confirmation.

    For technical questions regarding this item, or to correct its authors, title, abstract, bibliographic or download information, contact: PROF.IR.DR.Mohid Jailani Mohd Nor (email available below). General contact details of provider: https://kkgpublications.com/technology/ .

    Please note that corrections may take a couple of weeks to filter through the various RePEc services.

    IDEAS is a RePEc service. RePEc uses bibliographic data supplied by the respective publishers.