IDEAS home Printed from https://ideas.repec.org/a/eee/appene/v86y2009i10p2183-2191.html
   My bibliography  Save this article

Liquid piston gas compression

Author

Listed:
  • Van de Ven, James D.
  • Li, Perry Y.

Abstract

A liquid piston concept is proposed to improve the efficiency of gas compression and expansion. Because a liquid can conform to an irregular chamber volume, the surface area to volume ratio in the gas chamber can be maximized using a liquid piston. This creates near-isothermal operation, which minimizes energy lost to heat generation. A liquid piston eliminates gas leakage and replaces sliding seal friction with viscous friction. The liquid can also be used as a medium to carry heat into and out of the compression chamber. A simulation is presented of the heat transfer and frictional forces for a reciprocating piston and a liquid piston. In the application of an air compressor, with a pressure ratio of 9.5:1 and a cycle frequency of 20Â Hz, the liquid piston decreased the energy consumption by 19% over the reciprocating piston. The liquid piston and the reciprocating piston exhibited a total efficiency of 83% and 70% respectively. The liquid piston demonstrated significant improvements in the total compression efficiency in comparison to a conventional reciprocating piston. This gain in efficiency was accomplished through increasing the heat transfer during the gas compression by increasing the surface area to volume ratio in the compression chamber.

Suggested Citation

  • Van de Ven, James D. & Li, Perry Y., 2009. "Liquid piston gas compression," Applied Energy, Elsevier, vol. 86(10), pages 2183-2191, October.
    • Handle: RePEc:eee:appene:v:86:y:2009:i:10:p:2183-2191
    as

    Download full text from publisher

    File URL: http://www.sciencedirect.com/science/article/pii/S0306-2619(08)00321-8
    Download Restriction: Full text for ScienceDirect subscribers only
    ---><---

    As the access to this document is restricted, you may want to search for a different version of it.

    References listed on IDEAS

    as
    1. Klüppel, Rogerio P. & Gurgel, JoséMaurício M., 1998. "Thermodynamic cycle of a liquid piston pump," Renewable Energy, Elsevier, vol. 13(2), pages 261-268.
    2. Vimmr, J., 2003. "Mathematical modelling of compressible inviscid fluid flow through a sealing gap in the screw compressor," Mathematics and Computers in Simulation (MATCOM), Elsevier, vol. 61(3), pages 187-197.
    Full references (including those not matched with items on IDEAS)

    Most related items

    These are the items that most often cite the same works as this one and are cited by the same works as this one.
    1. Wang, Kai & Sanders, Seth R. & Dubey, Swapnil & Choo, Fook Hoong & Duan, Fei, 2016. "Stirling cycle engines for recovering low and moderate temperature heat: A review," Renewable and Sustainable Energy Reviews, Elsevier, vol. 62(C), pages 89-108.
    2. Delgado-Torres, Agustín M., 2009. "Solar thermal heat engines for water pumping: An update," Renewable and Sustainable Energy Reviews, Elsevier, vol. 13(2), pages 462-472, February.
    3. Jokar, H. & Tavakolpour-Saleh, A.R., 2015. "A novel solar-powered active low temperature differential Stirling pump," Renewable Energy, Elsevier, vol. 81(C), pages 319-337.
    4. Semmari, Hamza & Stitou, Driss & Mauran, Sylvain, 2012. "A novel Carnot-based cycle for ocean thermal energy conversion," Energy, Elsevier, vol. 43(1), pages 361-375.
    5. Van de Ven, James D., 2009. "Mobile hydraulic power supply: Liquid piston Stirling engine pump," Renewable Energy, Elsevier, vol. 34(11), pages 2317-2322.
    6. Ngangué, Max Ndamé & Stouffs, Pascal, 2020. "Dynamic simulation of an original Joule cycle liquid pistons hot air Ericsson engine," Energy, Elsevier, vol. 190(C).

    Corrections

    All material on this site has been provided by the respective publishers and authors. You can help correct errors and omissions. When requesting a correction, please mention this item's handle: RePEc:eee:appene:v:86:y:2009:i:10:p:2183-2191. See general information about how to correct material in RePEc.

    If you have authored this item and are not yet registered with RePEc, we encourage you to do it here. This allows to link your profile to this item. It also allows you to accept potential citations to this item that we are uncertain about.

    If CitEc recognized a bibliographic reference but did not link an item in RePEc to it, you can help with this form .

    If you know of missing items citing this one, you can help us creating those links by adding the relevant references in the same way as above, for each refering item. If you are a registered author of this item, you may also want to check the "citations" tab in your RePEc Author Service profile, as there may be some citations waiting for confirmation.

    For technical questions regarding this item, or to correct its authors, title, abstract, bibliographic or download information, contact: Catherine Liu (email available below). General contact details of provider: http://www.elsevier.com/wps/find/journaldescription.cws_home/405891/description#description .

    Please note that corrections may take a couple of weeks to filter through the various RePEc services.

    IDEAS is a RePEc service. RePEc uses bibliographic data supplied by the respective publishers.