IDEAS home Printed from https://ideas.repec.org/a/eee/appene/v114y2014icp434-444.html
   My bibliography  Save this article

Effect of kaolin additive on PM2.5 reduction during pulverized coal combustion: Importance of sodium and its occurrence in coal

Author

Listed:
  • Si, Junping
  • Liu, Xiaowei
  • Xu, Minghou
  • Sheng, Lei
  • Zhou, Zijian
  • Wang, Chao
  • Zhang, Yang
  • Seo, Yong-Chil

Abstract

Little work has been performed on the importance of sodium and its occurrence in coal to PM2.5 (particles less than 2.5μm in aerodynamic diameter) reduction by kaolin during O2/N2 combustion and O2/CO2 combustion at high temperatures. In this study, the combustion experiment of a treated low-sodium coal with sodium aluminosilicate additive was conducted in a lab-scale drop tube furnace (DTF) at 1500°C to reveal the contribution of mineral melting and coalescence to PM2.5 reduction. Meanwhile, two typical Na-loaded coals (in which the sodium was loaded in the form of NaCl and sodium carboxylate, respectively) with kaolin added were also burnt under O2/N2 and O2/CO2 atmospheres to investigate the effect of interaction between kaolin and different chemical form sodium on PM2.5 reduction. The results show that sodium aluminosilicate is able to promote the migration of PM0.5–2.5 (particles in aerodynamic diameter of 0.5–2.5μm) to form coarse particles. Due to the stronger reactivity of sodium carboxylate reacting with kaolin than that of NaCl, PM0.2–0.5 (particles in aerodynamic diameter of 0.2–0.5μm) decreases more significantly in the combustion when adding kaolin into the NaAc-loaded coal than into NaCl-loaded coal. In addition, the PM0.2–0.5 reduction in O2/CO2 combustion is lower than that in O2/N2 combustion owing to the less vaporization of metals and the slower diffusion rate of vapors in the O2/CO2 atmosphere in comparison to those in the O2/N2 atmosphere. The mineral coalescence varied in interactions of kaolin with NaAc and NaCl. Besides, the PM0.5–2.5 emission differed as a result of differences in coal characteristic and the atmosphere, and this would cause the difference of collision frequency between particles and additive. With the joint actions of mineral coalescence and particle collision, the NaAc-loaded coal has a higher PM0.5–2.5 reduction by kaolin than NaCl-loaded coal, especially under the O2/N2 combustion. An expression describing the relationship of PM0.5–2.5 reduction, mineral coalescence and particle collision was fitted and it is found that the mineral coalescence has a stronger influence than particle collision on PM0.5–2.5 reduction by kaolin.

Suggested Citation

  • Si, Junping & Liu, Xiaowei & Xu, Minghou & Sheng, Lei & Zhou, Zijian & Wang, Chao & Zhang, Yang & Seo, Yong-Chil, 2014. "Effect of kaolin additive on PM2.5 reduction during pulverized coal combustion: Importance of sodium and its occurrence in coal," Applied Energy, Elsevier, vol. 114(C), pages 434-444.
  • Handle: RePEc:eee:appene:v:114:y:2014:i:c:p:434-444
    DOI: 10.1016/j.apenergy.2013.10.002
    as

    Download full text from publisher

    File URL: http://www.sciencedirect.com/science/article/pii/S0306261913008222
    Download Restriction: Full text for ScienceDirect subscribers only

    File URL: https://libkey.io/10.1016/j.apenergy.2013.10.002?utm_source=ideas
    LibKey link: if access is restricted and if your library uses this service, LibKey will redirect you to where you can use your library subscription to access this item
    ---><---

    As the access to this document is restricted, you may want to search for a different version of it.

    References listed on IDEAS

    as
    1. Wang, Chang’an & Zhang, Xiaoming & Liu, Yinhe & Che, Defu, 2012. "Pyrolysis and combustion characteristics of coals in oxyfuel combustion," Applied Energy, Elsevier, vol. 97(C), pages 264-273.
    2. Hu, Yukun & Yan, Jinyue & Li, Hailong, 2012. "Effects of flue gas recycle on oxy-coal power generation systems," Applied Energy, Elsevier, vol. 97(C), pages 255-263.
    3. Álvarez, L. & Gharebaghi, M. & Jones, J.M. & Pourkashanian, M. & Williams, A. & Riaza, J. & Pevida, C. & Pis, J.J. & Rubiera, F., 2013. "CFD modeling of oxy-coal combustion: Prediction of burnout, volatile and NO precursors release," Applied Energy, Elsevier, vol. 104(C), pages 653-665.
    4. Geier, M. & Shaddix, C.R. & Davis, K.A. & Shim, H.-S., 2012. "On the use of single-film models to describe the oxy-fuel combustion of pulverized coal char," Applied Energy, Elsevier, vol. 93(C), pages 675-679.
    Full references (including those not matched with items on IDEAS)

    Citations

    Citations are extracted by the CitEc Project, subscribe to its RSS feed for this item.
    as


    Cited by:

    1. Wang, Wenyu & Wen, Chang & Liu, Tianyu & Li, Changkang & Chen, Lichun & Wu, Jianqun & Shao, Yuhao & Liu, Enze, 2020. "Effects of various occurrence modes of inorganic components on the emissions of PM10 during torrefied biomass combustion under air and oxy-fuel conditions," Applied Energy, Elsevier, vol. 259(C).
    2. Xu, Yishu & Liu, Xiaowei & Zhou, Zijian & Sheng, Lei & Wang, Chao & Xu, Minghou, 2014. "The role of steam in silica vaporization and ultrafine particulate matter formation during wet oxy-coal combustion," Applied Energy, Elsevier, vol. 133(C), pages 144-151.
    3. Liu, Yingzu & He, Yong & Wang, Zhihua & Xia, Jun & Wan, Kaidi & Whiddon, Ronald & Cen, Kefa, 2018. "Characteristics of alkali species release from a burning coal/biomass blend," Applied Energy, Elsevier, vol. 215(C), pages 523-531.
    4. Yang, Wei & Zhu, Youjian & Cheng, Wei & Sang, Huiying & Xu, Hanshen & Yang, Haiping & Chen, Hanping, 2018. "Effect of minerals and binders on particulate matter emission from biomass pellets combustion," Applied Energy, Elsevier, vol. 215(C), pages 106-115.
    5. Dai, C. & Cai, X.H. & Cai, Y.P. & Huang, G.H., 2014. "A simulation-based fuzzy possibilistic programming model for coal blending management with consideration of human health risk under uncertainty," Applied Energy, Elsevier, vol. 133(C), pages 1-13.
    6. Fan, He & Zhang, Yu-fei & Su, Zhi-gang & Wang, Ben, 2017. "A dynamic mathematical model of an ultra-supercritical coal fired once-through boiler-turbine unit," Applied Energy, Elsevier, vol. 189(C), pages 654-666.
    7. Li Zhang & Jingchong Yan & Qitong Yang & Zhiping Lei & Zhao Lei & Zhanku Li & Shibiao Ren & Zhicai Wang & Hengfu Shui, 2022. "Co-Firing Zhundong Coal with Its Gangue: Combustion Performance, Sodium Retention and Ash Fusion Behaviors," Sustainability, MDPI, vol. 14(24), pages 1-14, December.

    Most related items

    These are the items that most often cite the same works as this one and are cited by the same works as this one.
    1. Yin, Chungen & Yan, Jinyue, 2016. "Oxy-fuel combustion of pulverized fuels: Combustion fundamentals and modeling," Applied Energy, Elsevier, vol. 162(C), pages 742-762.
    2. Xu, Mingxin & Li, Shiyuan & Wu, Yinghai & Jia, Lufei & Lu, Qinggang, 2017. "The characteristics of recycled NO reduction over char during oxy-fuel fluidized bed combustion," Applied Energy, Elsevier, vol. 190(C), pages 553-562.
    3. Xu, Yishu & Liu, Xiaowei & Zhou, Zijian & Sheng, Lei & Wang, Chao & Xu, Minghou, 2014. "The role of steam in silica vaporization and ultrafine particulate matter formation during wet oxy-coal combustion," Applied Energy, Elsevier, vol. 133(C), pages 144-151.
    4. Hu, Yukun & Li, Hailong & Yan, Jinyue, 2014. "Numerical investigation of heat transfer characteristics in utility boilers of oxy-coal combustion," Applied Energy, Elsevier, vol. 130(C), pages 543-551.
    5. Pablo J. Arauzo & María Atienza-Martínez & Javier Ábrego & Maciej P. Olszewski & Zebin Cao & Andrea Kruse, 2020. "Combustion Characteristics of Hydrochar and Pyrochar Derived from Digested Sewage Sludge," Energies, MDPI, vol. 13(16), pages 1-15, August.
    6. Zhang, Minkai & Guo, Yincheng, 2013. "Rate based modeling of absorption and regeneration for CO2 capture by aqueous ammonia solution," Applied Energy, Elsevier, vol. 111(C), pages 142-152.
    7. Xu, Cheng & Xin, Tuantuan & Xu, Gang & Li, Xiaosa & Liu, Wenyi & Yang, Yongping, 2017. "Thermodynamic analysis of a novel solar-hybrid system for low-rank coal upgrading and power generation," Energy, Elsevier, vol. 141(C), pages 1737-1749.
    8. Meng Yue & Guoqian Ma & Yuetao Shi, 2020. "Analysis of Gas Recirculation Influencing Factors of a Double Reheat 1000 MW Unit with the Reheat Steam Temperature under Control," Energies, MDPI, vol. 13(16), pages 1-22, August.
    9. Oboirien, B.O. & Thulari, V. & North, B.C., 2014. "Major and trace elements in coal bottom ash at different oxy coal combustion conditions," Applied Energy, Elsevier, vol. 129(C), pages 207-216.
    10. Bu, Changsheng & Gómez-Barea, Alberto & Chen, Xiaoping & Leckner, Bo & Liu, Daoyin & Pallarès, David & Lu, Ping, 2016. "Effect of CO2 on oxy-fuel combustion of coal-char particles in a fluidized bed: Modeling and comparison with the conventional mode of combustion," Applied Energy, Elsevier, vol. 177(C), pages 247-259.
    11. Li, Shiyuan & Xu, Mingxin & Jia, Lufei & Tan, Li & Lu, Qinggang, 2016. "Influence of operating parameters on N2O emission in O2/CO2 combustion with high oxygen concentration in circulating fluidized bed," Applied Energy, Elsevier, vol. 173(C), pages 197-209.
    12. Kartal, Furkan & Dalbudak, Yağmur & Özveren, Uğur, 2023. "Prediction of thermal degradation of biopolymers in biomass under pyrolysis atmosphere by means of machine learning," Renewable Energy, Elsevier, vol. 204(C), pages 774-787.
    13. Mansir, Ibrahim B. & Ben-Mansour, Rached & Habib, Mohamed A., 2018. "Oxy-fuel combustion in a two-pass oxygen transport reactor for fire tube boiler application," Applied Energy, Elsevier, vol. 229(C), pages 828-840.
    14. Chen, Jianbiao & Gao, Shuaifei & Xu, Fang & Xu, Wenhao & Yang, Yuanjiang & Kong, Depeng & Wang, Yinfeng & Yao, Huicong & Chen, Haijun & Zhu, Yuezhao & Mu, Lin, 2022. "Influence of moisture and feedstock form on the pyrolysis behaviors, pyrolytic gas production, and residues micro-structure evolutions of an industrial sludge from a steel production enterprise," Energy, Elsevier, vol. 248(C).
    15. Prabu, V., 2015. "Integration of in-situ CO2-oxy coal gasification with advanced power generating systems performing in a chemical looping approach of clean combustion," Applied Energy, Elsevier, vol. 140(C), pages 1-13.
    16. Chi, Chung-Cheng & Lin, Ta-Hui, 2013. "Oxy-oil combustion characteristics of an existing furnace," Applied Energy, Elsevier, vol. 102(C), pages 923-930.
    17. Li, Tian & Niu, Yanqing & Wang, Liang & Shaddix, Christopher & Løvås, Terese, 2018. "High temperature gasification of high heating-rate chars using a flat-flame reactor," Applied Energy, Elsevier, vol. 227(C), pages 100-107.
    18. Xu, Hao & Cheng, Shuo & Hungwe, Douglas & Yoshikawa, Kunio & Takahashi, Fumitake, 2022. "Co-pyrolysis coupled with torrefaction enhances hydrocarbons production from rice straw and oil sludge: The effect of torrefaction on co-pyrolysis synergistic behaviors," Applied Energy, Elsevier, vol. 327(C).
    19. Gil, María V. & Riaza, Juan & Álvarez, Lucía & Pevida, Covadonga & Rubiera, Fernando, 2015. "Biomass devolatilization at high temperature under N2 and CO2: Char morphology and reactivity," Energy, Elsevier, vol. 91(C), pages 655-662.
    20. Choi, Munkyoung & Cho, Minki & Lee, J.W., 2016. "Empirical formula for the mass flux in chemical absorption of CO2 with ammonia droplets," Applied Energy, Elsevier, vol. 164(C), pages 1-9.

    More about this item

    Keywords

    PM2.5 reduction; Kaolin; Sodium; Coal combustion;
    All these keywords.

    JEL classification:

    Statistics

    Access and download statistics

    Corrections

    All material on this site has been provided by the respective publishers and authors. You can help correct errors and omissions. When requesting a correction, please mention this item's handle: RePEc:eee:appene:v:114:y:2014:i:c:p:434-444. See general information about how to correct material in RePEc.

    If you have authored this item and are not yet registered with RePEc, we encourage you to do it here. This allows to link your profile to this item. It also allows you to accept potential citations to this item that we are uncertain about.

    If CitEc recognized a bibliographic reference but did not link an item in RePEc to it, you can help with this form .

    If you know of missing items citing this one, you can help us creating those links by adding the relevant references in the same way as above, for each refering item. If you are a registered author of this item, you may also want to check the "citations" tab in your RePEc Author Service profile, as there may be some citations waiting for confirmation.

    For technical questions regarding this item, or to correct its authors, title, abstract, bibliographic or download information, contact: Catherine Liu (email available below). General contact details of provider: http://www.elsevier.com/wps/find/journaldescription.cws_home/405891/description#description .

    Please note that corrections may take a couple of weeks to filter through the various RePEc services.

    IDEAS is a RePEc service. RePEc uses bibliographic data supplied by the respective publishers.