IDEAS home Printed from https://ideas.repec.org/a/eee/appene/v108y2013icp108-120.html
   My bibliography  Save this article

Constant rate thermal analysis for enhancing the long-term CO2 capture of CaO at Ca-looping conditions

Author

Listed:
  • Valverde, Jose M.
  • Sanchez-Jimenez, Pedro E.
  • Perejon, Antonio
  • Perez-Maqueda, Luis A.

Abstract

Experimental results are reported on the (Ca-looping) multicyclic CO2 capture of CaO and nanosilica/CaO composites derived from Ca(OH)2 and nanosilica/Ca(OH)2 dry mixtures subjected in situ to linear and constant rate thermal analysis (CRTA) preheating programs in either air or air/CO2 atmospheres. By means of CRTA preheating the rates of the reactions taking place during pretreatment are kept at a constant and small value along the entire process. In agreement with a pore skeleton model, previously proposed in the literature for explaining the behavior of natural limestones thermally pretreated, our results suggest that air/CO2-CRTA pretreatment yields a thermally stable hard skeleton of poorly reactive CaO on which a soft skeleton of reactive CaO would be supported. The sorbent subjected to this preheating program exhibits a reactivation in the very first carbonation/calcination cycles, after which CaO conversion decays slowly with the cycle number. In contrast, linearly or air-CRTA preheated sorbents show a significant decrease of CaO conversion within the first cycles. In the latter case, CaO multicyclic conversion fits well to a model where it is assumed that the progressive reduction of surface area as the number of carbonation/calcination cycles is increased obeys to sintering of the preheated sorbent skeleton as it is subjected to repeated calcinations during cycling. In the former case, CaO conversion data conforms to the prediction by a model in which the loss of surface area is mainly due to sintering of a nascent CaO soft skeleton regenerated in the diffusive carbonation phase, which is enhanced by the air/CO2-CRTA pretreatment. As regards the effect of nanosilica, the results indicate that it slows down CaO sintering during pretreatment, which hinders the development of a stable CaO skeleton thus hampering reactivation and stabilization of conversion. On the other hand, as CaO sintering is also lessened during looping calcination, nanosilica is useful to increase the absolute values of CaO conversion.

Suggested Citation

  • Valverde, Jose M. & Sanchez-Jimenez, Pedro E. & Perejon, Antonio & Perez-Maqueda, Luis A., 2013. "Constant rate thermal analysis for enhancing the long-term CO2 capture of CaO at Ca-looping conditions," Applied Energy, Elsevier, vol. 108(C), pages 108-120.
    • Handle: RePEc:eee:appene:v:108:y:2013:i:c:p:108-120
    DOI: 10.1016/j.apenergy.2013.03.013
    as

    Download full text from publisher

    File URL: http://www.sciencedirect.com/science/article/pii/S0306261913001992
    Download Restriction: Full text for ScienceDirect subscribers only
    File URL: https://libkey.io/10.1016/j.apenergy.2013.03.013?utm_source=ideas
    LibKey link: if access is restricted and if your library uses this service, LibKey will redirect you to where you can use your library subscription to access this item
    ---><---

    As the access to this document is restricted, you may want to search for a different version of it.

    References listed on IDEAS

    as
    1. Lisbona, Pilar & Martínez, Ana & Romeo, Luis M., 2013. "Hydrodynamical model and experimental results of a calcium looping cycle for CO2 capture," Applied Energy, Elsevier, vol. 101(C), pages 317-322.
    2. Chen, Huichao & Zhao, Changsui & Yang, Yanmei & Zhang, Pingping, 2012. "CO2 capture and attrition performance of CaO pellets with aluminate cement under pressurized carbonation," Applied Energy, Elsevier, vol. 91(1), pages 334-340.
    Full references (including those not matched with items on IDEAS)

    Citations

    Citations are extracted by the CitEc Project, subscribe to its RSS feed for this item.
    as


    Cited by:

    1. Yan, J. & Zhao, C.Y. & Pan, Z.H., 2017. "The effect of CO2 on Ca(OH)2 and Mg(OH)2 thermochemical heat storage systems," Energy, Elsevier, vol. 124(C), pages 114-123.
    2. Valverde, J.M. & Sanchez-Jimenez, P.E. & Perez-Maqueda, L.A., 2014. "Calcium-looping for post-combustion CO2 capture. On the adverse effect of sorbent regeneration under CO2," Applied Energy, Elsevier, vol. 126(C), pages 161-171.
    3. Li, Kaimin & Jiang, Jianguo & Yan, Feng & Tian, Sicong & Chen, Xuejing, 2014. "The influence of polyethyleneimine type and molecular weight on the CO2 capture performance of PEI-nano silica adsorbents," Applied Energy, Elsevier, vol. 136(C), pages 750-755.
    4. Lee, Jaehee & Han, Sang-Jun & Wee, Jung-Ho, 2014. "Synthesis of dry sorbents for carbon dioxide capture using coal fly ash and its performance," Applied Energy, Elsevier, vol. 131(C), pages 40-47.
    5. Perejón, Antonio & Romeo, Luis M. & Lara, Yolanda & Lisbona, Pilar & Martínez, Ana & Valverde, Jose Manuel, 2016. "The Calcium-Looping technology for CO2 capture: On the important roles of energy integration and sorbent behavior," Applied Energy, Elsevier, vol. 162(C), pages 787-807.
    6. Cho, Won Chul & Lee, Do Yeon & Seo, Myung Won & Kim, Sang Done & Kang, KyoungSoo & Bae, Ki Kwang & Kim, Change Hee & Jeong, SeongUk & Park, Chu Sik, 2014. "Continuous operation characteristics of chemical looping hydrogen production system," Applied Energy, Elsevier, vol. 113(C), pages 1667-1674.
    7. Li, Yingjie & Su, Mengying & Xie, Xin & Wu, Shuimu & Liu, Changtian, 2015. "CO2 capture performance of synthetic sorbent prepared from carbide slag and aluminum nitrate hydrate by combustion synthesis," Applied Energy, Elsevier, vol. 145(C), pages 60-68.
    8. Hanak, Dawid P. & Jenkins, Barrie G. & Kruger, Tim & Manovic, Vasilije, 2017. "High-efficiency negative-carbon emission power generation from integrated solid-oxide fuel cell and calciner," Applied Energy, Elsevier, vol. 205(C), pages 1189-1201.
    9. Chen, Huichao & Zhao, Changsui & Yu, Weiwei, 2013. "Calcium-based sorbent doped with attapulgite for CO2 capture," Applied Energy, Elsevier, vol. 112(C), pages 67-74.
    10. Shi, Jiewen & Li, Yingjie & Zhang, Qing & Ma, Xiaotong & Duan, Lunbo & Zhou, Xingang, 2017. "CO2 capture performance of a novel synthetic CaO/sepiolite sorbent at calcium looping conditions," Applied Energy, Elsevier, vol. 203(C), pages 412-421.
    11. Valverde, J.M. & Sanchez-Jimenez, P.E. & Perez-Maqueda, L.A. & Quintanilla, M.A.S. & Perez-Vaquero, J., 2014. "Role of crystal structure on CO2 capture by limestone derived CaO subjected to carbonation/recarbonation/calcination cycles at Ca-looping conditions," Applied Energy, Elsevier, vol. 125(C), pages 264-275.
    12. Wang, Wenjing & Li, Yingjie & Xie, Xin & Sun, Rongyue, 2014. "Effect of the presence of HCl on cyclic CO2 capture of calcium-based sorbent in calcium looping process," Applied Energy, Elsevier, vol. 125(C), pages 246-253.
    13. Xie, Xin & Li, Yingjie & Wang, Wenjing & Shi, Lei, 2014. "HCl removal using cycled carbide slag from calcium looping cycles," Applied Energy, Elsevier, vol. 135(C), pages 391-401.
    14. Ma, Xiaotong & Li, Yingjie & Shi, Lei & He, Zirui & Wang, Zeyan, 2016. "Fabrication and CO2 capture performance of magnesia-stabilized carbide slag by by-product of biodiesel during calcium looping process," Applied Energy, Elsevier, vol. 168(C), pages 85-95.
    15. Valverde, J.M. & Raganati, F. & Quintanilla, M.A.S. & Ebri, J.M.P. & Ammendola, P. & Chirone, R., 2013. "Enhancement of CO2 capture at Ca-looping conditions by high-intensity acoustic fields," Applied Energy, Elsevier, vol. 111(C), pages 538-549.
    16. Lara, Yolanda & Lisbona, Pilar & Martínez, Ana & Romeo, Luis M., 2013. "Design and analysis of heat exchanger networks for integrated Ca-looping systems," Applied Energy, Elsevier, vol. 111(C), pages 690-700.
    17. Zhang, Zhonghua & Wang, Baodong & Sun, Qi & Zheng, Lingru, 2014. "A novel method for the preparation of CO2 sorption sorbents with high performance," Applied Energy, Elsevier, vol. 123(C), pages 179-184.
    18. Witoon, Thongthai & Mungcharoen, Thumrongrut & Limtrakul, Jumras, 2014. "Biotemplated synthesis of highly stable calcium-based sorbents for CO2 capture via a precipitation method," Applied Energy, Elsevier, vol. 118(C), pages 32-40.
    19. Zhao, Yunlei & Jin, Bo & Luo, Xiao & Liang, Zhiwu, 2021. "Thermodynamic evaluation and experimental investigation of CaO-assisted Fe-based chemical looping reforming process for syngas production," Applied Energy, Elsevier, vol. 288(C).
    20. Zhang, Wan & Li, Yingjie & He, Zirui & Ma, Xiaotong & Song, Haiping, 2017. "CO2 capture by carbide slag calcined under high-concentration steam and energy requirement in calcium looping conditions," Applied Energy, Elsevier, vol. 206(C), pages 869-878.
    21. Sanchez-Jimenez, P.E. & Perez-Maqueda, L.A. & Valverde, J.M., 2014. "Nanosilica supported CaO: A regenerable and mechanically hard CO2 sorbent at Ca-looping conditions," Applied Energy, Elsevier, vol. 118(C), pages 92-99.
    22. Valverde, J.M. & Sanchez-Jimenez, P.E. & Perez-Maqueda, L.A., 2014. "Role of precalcination and regeneration conditions on postcombustion CO2 capture in the Ca-looping technology," Applied Energy, Elsevier, vol. 136(C), pages 347-356.

    Most related items

    These are the items that most often cite the same works as this one and are cited by the same works as this one.
    1. Perejón, Antonio & Romeo, Luis M. & Lara, Yolanda & Lisbona, Pilar & Martínez, Ana & Valverde, Jose Manuel, 2016. "The Calcium-Looping technology for CO2 capture: On the important roles of energy integration and sorbent behavior," Applied Energy, Elsevier, vol. 162(C), pages 787-807.
    2. Itskos, Grigorios & Grammelis, Panagiotis & Scala, Fabrizio & Pawlak-Kruczek, Halina & Coppola, Antonio & Salatino, Piero & Kakaras, Emmanuel, 2013. "A comparative characterization study of Ca-looping natural sorbents," Applied Energy, Elsevier, vol. 108(C), pages 373-382.
    3. Lara, Yolanda & Lisbona, Pilar & Martínez, Ana & Romeo, Luis M., 2013. "Design and analysis of heat exchanger networks for integrated Ca-looping systems," Applied Energy, Elsevier, vol. 111(C), pages 690-700.
    4. Gu, Haiming & Shen, Laihong & Zhong, Zhaoping & Niu, Xin & Liu, Weidong & Ge, Huijun & Jiang, Shouxi & Wang, Lulu, 2015. "Cement/CaO-modified iron ore as oxygen carrier for chemical looping combustion of coal," Applied Energy, Elsevier, vol. 157(C), pages 314-322.
    5. Aisyah, L. & Ashman, P.J. & Kwong, C.W., 2013. "Performance of coal fly-ash based oxygen carrier for the chemical looping combustion of synthesis gas," Applied Energy, Elsevier, vol. 109(C), pages 44-50.
    6. Valverde, J.M. & Raganati, F. & Quintanilla, M.A.S. & Ebri, J.M.P. & Ammendola, P. & Chirone, R., 2013. "Enhancement of CO2 capture at Ca-looping conditions by high-intensity acoustic fields," Applied Energy, Elsevier, vol. 111(C), pages 538-549.
    7. Shrestha, Siddhartha & Ali, Brahim Si & Binti Hamid, Mahar Diana, 2016. "Cold flow model of dual fluidized bed: A review," Renewable and Sustainable Energy Reviews, Elsevier, vol. 53(C), pages 1529-1548.
    8. Giuffrida, A. & Bonalumi, D. & Lozza, G., 2013. "Amine-based post-combustion CO2 capture in air-blown IGCC systems with cold and hot gas clean-up," Applied Energy, Elsevier, vol. 110(C), pages 44-54.
    9. Su, Chenglin & Duan, Lunbo & Donat, Felix & Anthony, Edward John, 2018. "From waste to high value utilization of spent bleaching clay in synthesizing high-performance calcium-based sorbent for CO2 capture," Applied Energy, Elsevier, vol. 210(C), pages 117-126.
    10. Zhang, Xiaosong & Jin, Hongguang, 2013. "Thermodynamic analysis of chemical-looping hydrogen generation," Applied Energy, Elsevier, vol. 112(C), pages 800-807.
    11. Yu, Ching-tsung & Kuo, Huan-ting & Chen, Yi-ming, 2016. "Carbon dioxide removal using calcium aluminate carbonates on titanic oxide under warm-gas conditions," Applied Energy, Elsevier, vol. 162(C), pages 1122-1130.
    12. Dou, Binlin & Song, Yongchen & Wang, Chao & Chen, Haisheng & Yang, Mingjun & Xu, Yujie, 2014. "Hydrogen production by enhanced-sorption chemical looping steam reforming of glycerol in moving-bed reactors," Applied Energy, Elsevier, vol. 130(C), pages 342-349.
    13. Valverde, J.M. & Sanchez-Jimenez, P.E. & Perez-Maqueda, L.A., 2014. "Calcium-looping for post-combustion CO2 capture. On the adverse effect of sorbent regeneration under CO2," Applied Energy, Elsevier, vol. 126(C), pages 161-171.
    14. Gong, Xuzhong & Zhang, Tong & Zhang, Junqiang & Wang, Zhi & Liu, Junhao & Cao, Jianwei & Wang, Chuan, 2022. "Recycling and utilization of calcium carbide slag - current status and new opportunities," Renewable and Sustainable Energy Reviews, Elsevier, vol. 159(C).
    15. Valverde, J.M. & Sanchez-Jimenez, P.E. & Perez-Maqueda, L.A. & Quintanilla, M.A.S. & Perez-Vaquero, J., 2014. "Role of crystal structure on CO2 capture by limestone derived CaO subjected to carbonation/recarbonation/calcination cycles at Ca-looping conditions," Applied Energy, Elsevier, vol. 125(C), pages 264-275.
    16. Shuai Zhang & Rui Xiao, 2018. "Comparison of pyrite cinder with synthetic and natural iron†based oxygen carriers in coal†fueled chemical†looping combustion," Greenhouse Gases: Science and Technology, Blackwell Publishing, vol. 8(1), pages 106-119, February.
    17. Li, Yingjie & Su, Mengying & Xie, Xin & Wu, Shuimu & Liu, Changtian, 2015. "CO2 capture performance of synthetic sorbent prepared from carbide slag and aluminum nitrate hydrate by combustion synthesis," Applied Energy, Elsevier, vol. 145(C), pages 60-68.
    18. Lisbona, Pilar & Martínez, Ana & Romeo, Luis M., 2013. "Hydrodynamical model and experimental results of a calcium looping cycle for CO2 capture," Applied Energy, Elsevier, vol. 101(C), pages 317-322.
    19. Cho, Won Chul & Lee, Do Yeon & Seo, Myung Won & Kim, Sang Done & Kang, KyoungSoo & Bae, Ki Kwang & Kim, Change Hee & Jeong, SeongUk & Park, Chu Sik, 2014. "Continuous operation characteristics of chemical looping hydrogen production system," Applied Energy, Elsevier, vol. 113(C), pages 1667-1674.
    20. Li, Bingyun & Duan, Yuhua & Luebke, David & Morreale, Bryan, 2013. "Advances in CO2 capture technology: A patent review," Applied Energy, Elsevier, vol. 102(C), pages 1439-1447.

    Corrections

    All material on this site has been provided by the respective publishers and authors. You can help correct errors and omissions. When requesting a correction, please mention this item's handle: RePEc:eee:appene:v:108:y:2013:i:c:p:108-120. See general information about how to correct material in RePEc.

    If you have authored this item and are not yet registered with RePEc, we encourage you to do it here. This allows to link your profile to this item. It also allows you to accept potential citations to this item that we are uncertain about.

    If CitEc recognized a bibliographic reference but did not link an item in RePEc to it, you can help with this form .

    If you know of missing items citing this one, you can help us creating those links by adding the relevant references in the same way as above, for each refering item. If you are a registered author of this item, you may also want to check the "citations" tab in your RePEc Author Service profile, as there may be some citations waiting for confirmation.

    For technical questions regarding this item, or to correct its authors, title, abstract, bibliographic or download information, contact: Catherine Liu (email available below). General contact details of provider: http://www.elsevier.com/wps/find/journaldescription.cws_home/405891/description#description .

    Please note that corrections may take a couple of weeks to filter through the various RePEc services.

    IDEAS is a RePEc service. RePEc uses bibliographic data supplied by the respective publishers.